Fuji Xerox DocuPrint CM225FW User Manual Download

Page: 12 / 344

Using This Guide

Using This Guide



Organization

This guide is organized into the following chapters. The summary of each chapter is as follows:



Conventions

•

In this guide, personal computers and workstations are collectively called "computers".

•

The following terms are used throughout this guide:

IMPORTANT:

•

Important information that must be read and followed.

NOTE:

•

Additional information that merits emphasis.

See also:

•

References within this guide.

•

Orientation of documents or paper is described in this guide as follows:

, Long Edge Feed (LEF): Loading the document or paper in landscape orientation.

, Short Edge Feed (SEF): Loading the document or paper in portrait orientation.

•

Some of the items in the screen shots and illustrations may not be displayed or available depending on your
printer model.

Specifications

Describes the printer specifications.

Basic Operation

Describes the main components of the printer, the power saver mode, and how to
turn on/off the printer.

Printer Management Software

Describes the software available for the printer.

Printer Connection and Software
Installation

Describes the basic information about how to connect the printer to your computer
and how to install the print driver.

Printing Basics

Describes the supported paper, how to load paper, and how to print data using
various print features.

Copying

Describes how to copy documents and the adjustment features.

Scanning

Describes how to set and use the Scan features.

Faxing

Describes how to set and use the Fax features.

Using the Operator Panel Menus
and Keypad

Describes the setting items available on the operator panel, their setup
procedures, and how to use the number pad.

Using the Server Address Book
and Server Phone Book

Describes how to set the server address book and server phone book.

Digital Certificates

Describes how to create and manage digital certificates.

Troubleshooting

Describes the troubleshooting tips for printer problems such as paper jams.

Maintenance

Describes how to clean the printer, how to replace toner cartridges, and how to
see the printer status.

Contacting Fuji Xerox

Describes support information.

LEF Orientation

SEF Orientation

Paper feed direction

Summary of Contents for DocuPrint CM225FW
























































































































































































































































































































































Search results

Summary of Contents for DocuPrint CM225FW

Reviews:

Related manuals for DocuPrint CM225FW

Brands by name

Popular brands

Fuji Xerox DocuPrint CM225FW, User Manual

Search results

Summary of Contents for DocuPrint CM225FW

Reviews:

Related manuals for DocuPrint CM225FW

Brands by name

Popular brands