background image

Machine Compatibility:
Fuji Xerox 20
IBM Infoprint 20/ 4320
Apple LaserWriter 8500
Fujitsu 307A
Casio CP-DTC8
APTI-E 840
Ricoh NX5000

Anhydrous Isopropyl
Alcohol
Padding Powder
Soft Lint- Free Cloth
Swabs
Seal
640gm Toner
Drum
Doctor Blade
Wiper Blade

Punch
Hammer
Needle Nose Pliers
Diagonal Cutters
Philips Screwdriver
Small Flat Blade Screwdriver

Technical Instructions

Printers

Supplies

Tools

1

4019 TECH

Photo 1

The Fuji Xerox P-880 engine was first found in the Apple Laserwriter 8500 back in

August of 1997, then two years later IBM released the Infoprint 20 using the same
engine.The large format Fuji Xerox P-880 engine propels its machines to a speed up
to 20 pages per minute at 600dpi and can handle multiple paper sizes including
11”x17”. The all-in-one cartridge design is similar to other Fuji Xerox engines 
and looks like a cross between the Xerox N32 and the Xerox N17. 640 grams of
UltraFine toner fills the toner hopper and delivers 14,000 pages at 5% coverage.
However, with TonerMiser technology the machine can cut the toner usage in half
increasing the yield to 28,000 pages at 5% coverage.

Photo 2

Step 1

Using needle nose pliers or a spring hook,
remove the tension spring located on the
end of the cartridge.

(See Photo 1)

Step 2

With a pair of diagonal cutters remove
the cartridge pins located on each end
of the cartridge.

(See Photo 2 & 3)

Photo 3

E-mail: info@futuregraphicsllc.com   

Website:

www.futuregraphicsllc.com 

US 1 800 394.9900
Int’l +1 818 837.8100
FAX 1 800 394.9910
Int’l  +1 818 838.7047

DALLAS, USA

US 1 877 499.4989
Int’l +1 972 840.4989
FAX  1 877 774.1750
Int’l +1 972 840.1750

ATLANTA, USA

US 1 877 676.4223
Int’l +1 770 516.9488
FAX 1 877 337.7976
Int’l +1 770 516.7794

MIAMI, USA

US 1 800 595.429
Int’l +1 305 594.3396
FAX 1 800 522.8640
Int’l +1 305 594.3309

SANFORD,USA

US 1 800 786.9049
Int’l +1 919 775.4584
FAX 1 800 786.9049
Int’l +1 919 775.4584

TORONTO, CAN

CAN  1 877 848.0818
Int’l +1 905 712.9501
FAX 1 877 772.6773
Int’l +1 905 712.9502

NEW YORK, USA

US 1 800 431.7884
Int’l +1 631 345.0121
FAX 1 800 431.8812
Int’l +1 631345.0690

SYDNEY, AUS

AUS 1 800 003.100
Int’l +62 02 9648.2630
FAX 1800 004.302
Int’l +62 02 9548.2635

BUENOS AIRES, ARG

ARG 0810 444.2656
Int’l +011 4583.5900
FAX +011 4584.3100

MONTEVIDEO,URY

URY 02 902.7206
Int’l +5982 900.8358
FAX +5982 908.3816

JOHANNESBURG, S.A.

S.A. +27 11 974.6155
FAX +27 11 974.3593

MELBOURNE, AUS

AUS 1 800 003. 100
Int’l +62 03 9561.8102
FAX 1 800 004.302
Int’l +62 03 9561-7751

CORPORATE 

LOS ANGELES, USA

 

Summary of Contents for P-880









Reviews: