SS1807-N002
Installation
-
22/68
1.13 Power Source
Installation of this system must be performed according to EN 60601-1.
When installing this system, follow the descriptions below.
<Power connection for using equipment in combination>
The equipment which can be used in combination with this system is divided into the following three
types according to its power connection.
(1) Equipment which is directly combined with this system (Applicable to EN 60601-1)
The equipment that makes up this product and system.
Examples of such equipment are shown in Table 1.1.
(2) Equipment which can be used when its power is supplied from a power source other than the
cart in which this system is installed. (Applicable to EN 60601-1)
Examples of such equipment are shown in Table 1.2.
(3) Peripherals which are used when required power is supplied from an insulated transformer
applicable to EN 60601-1 (Applicable or conforming to EN 60601-1 or EN60950)
Examples of such equipment are shown in Table 1.3.
The equipment other than these three types may not be safe. Do not use such equipment.
In combination with any of the equipment above, all configurations shall comply with the requirement
for ME systems of EN 60601-1.
In any combination of the equipment above, all configurations must comply with the requirements of
ME systems of EN60601-1.
◆
Note
◆
・
These combinations are determined based on electrical safety. The performance of the equipment
depends on the specifications of each manufacturer.
Table 1.1 Equipment configuring the system
Type
Model
Processor
EP-6000
Data Keyboard
DK-6000U or DK-6000E
*1
Endoscope
700 system scopes
600 system scopes
500 system scopes
*1
:
The type of the data keyboard varies depending on the country.
Table 1.2 Medical equipment used when its power is supplied from other power source
Type
Model
Electrosurgical Unit
*2
-
*2
:
For electrosurgical units that can be combined, see the instruction manual of the endoscope.
Table 1.3 Peripherals used when its power is supplied from an insulated transformer
Type
Model
Ultrasonic Processor
SU-1,SP-900
LCD Monitor
CL-22(FUJIFILM), CL-24(FUJIFILM), CCL220/AR(JVC KENWOOD)
CCL244/AR(JVC KENWOOD)
Printer
UP-25MD(SONY), UP-55MD(SONY), UP-D25MD(SONY)
Video Recorder
HVO-3300MT(SONY), HVO-1000MD(SONY), HVO-550MD(SONY)
Summary of Contents for EP-6000
