background image

Œ、õö÷EG

tøK

Lx¶'

MNd,'›

:OPõö÷E

QGt。

R、öùEø

K:

STk

öù=ö

UV9

Xguö。

Y、ö

ZEø

K:

STLδ

ZŒx,@ýþö

Z,

]^。

\

]^àG

_

e,£dd`

Ëa

。b

eöZc

8*+,d

‰ýþöZ

@ýþe

 [,'ÿ

 ,(câf

Ó

=>]^úuûEöüâ

f。

7

g、

hiEø

3

STLjR¥

3hiŒx(™

klm,-./ø

3)。

\k( )

n

†op

、qr

,‘k( )n

b

e¢$s

tu

Ec

8*+†#¢

$s

、(ÆZ

,

dk( )v

[wx

hiy

†hi

1     ,

2                               ,

3                 ,

(

) 1

(

) 2

(

) 3

( )

1

( )

2

( )

3

7

1 Hood surface cleaning

After each use wipe the range hood s external surface with a soft cloth

2 Oil tray cleaning

It is recommended that the oil tray be emptied regularly

3

Filter cleaning

It is recommended that the filter be cleaned once a month

Remove

the rectifier panel before removing the filter by first pulling down the
front part of rectifier panel to open it and then detach the back part from the

clip. Loosen the filter mounting screws so that the filter can be removed.

Always use both hands to carefully grasp all parts being removed to prevent

them from falling and becoming damaged.
Please watch out for oil that has collected in the rectifier panel.

4.  Fan cleaning

It is recommended that the fan be cleaned once a year (this has to be
performed by a trained technician). As indicated in Diagram (1), first
remove the duct cover and the case cover plate, then, as indicated in
Diagram (2), loosen the bell mouth and the fan casing mounting screw
to remove the bell mouth and the fan guard and then finally, as indicated
in Diagram (3), turn the fan cap in a clockwise direction to remove the
fan.

.

:

,

'

.

.

:

.

.

.

Soft cloth

(12) The range hood is intended to be installed over a hob with up to four hob

elements or burners, no more than total 5.2kW.

12                      1        4

、Ãõö÷'

{|¥zÅ

} œ½ì

~Eñ

=|,

€z

@

5.2kW

Summary of Contents for FJS-900V













Reviews: