background image

Colour monitor 5110 FA

A26361-K872-Z100-1-5E19

English - 3

 

The ON/OFF switch does not disconnect the device from the mains voltage. To completely
disconnect the mains voltage, remove the power plug from the socket.

 

Lay all cables so that nobody can stand on them or trip over them. When attaching the device,
observe the relevant notes in the "Connecting the monitor" chapter.

 

No data transmission cable should be connected or disconnected during a thunderstorm.

 

Please ensure that no objects (e.g. necklaces, paperclips etc.) or liquids can get into the
interior of the device (this may cause an electrical shock or short circuit).

 

In emergencies (e.g. damaged casing, elements or cables, penetration of liquids or foreign
matter), switch off the unit, disconnect the power plug and contact your sales outlet or our Help
Desk.

 

The screen background lighting contains mercury. You must observe the applicable handling
and disposal safety regulations for fluorescent tubes.

 

Only qualified technicians should repair the device. Unauthorised opening and incorrect repair
may greatly endanger the user (electric shock, fire risk).

 

You may set only those resolutions and refresh rates specified in the "Technical data" chapter.
Otherwise you may damage your monitor. If you are in any doubt, contact your sales outlet or
our Help Desk.

 

Keep this operating manual together with your device. If you pass on the device to third parties,
you should include this manual.

Cleaning notes

 

Always pull out the power plug before you clean the monitor.

 

Do not clean any interior parts yourself, leave this job to a service technician.

 

Do not use any cleaning agents that contain abrasives or may corrode plastic.

 

Ensure that no liquid will run into the system.

 

Ensure that the ventilation areas of the monitor are free.

 

The display surface of the LCD monitor is sensitive to pressure and scratches. Clean it only
using a soft, slightly moistened cloth.

Wipe the monitor casing with a dry cloth. If the monitor is particularly dirty, use a cloth which has
been moistened in mild domestic detergent and then carefully wrung out.

Transport notes

 

Transport the monitor with care and only in its original packaging or another corresponding
packaging fit to protect it against knocks and jolts.

 

Never drop the LCD monitor (danger of glass breakage).

Summary of Contents for 5110 FA


























Reviews: