background image

 

Colour monitor SCENICVIEW B15-1A 

A26361-K938-Z100-2-5E19

 

English - 9 

 

2

3

1

4

  Lay the monitor on its face on a soft 

surface. 

  Remove the cover (2) and disconnect all 

cables. 

  Remove the four screws on the rear of the 

monitor (1). 

  Remove the covers (3 and 4) by pressing on 

the plastic parts and simultaneously pulling 
them outward. 

  Remove the three screws under each of the 

covers (3 and 4). 

You can now mount a swivel arm or a wall 
bracket as per VESA FPMPMI with 75 mm hole 
spacing.  
 

Note on mounting a swivel arm or a wall bracket 

For instructions on how to mount the swivel arm or wall bracket, please see the documentation for 
the swivel arm or wall bracket. 
We recommend always operating the monitor in the standard position (4:3, wide format, landscape 
mode). 

 

!

 

If you want to operate the monitor with a swivel arm or wall bracket in the portrait mode, it 
may only be turned by 90° clockwise.  

 

 

Permissible position of monitor in portrait mode:  
The buttons of the control panel are located on 
the left-hand side. 

Summary of Contents for SCENICVIEW B15-1A


































Reviews: