![background image](http://html.mh-extra.com/html/fujitsu/1740/1740_user-manual_120441129.webp)
4 Handling the Rack after Installation
129
E
3
Affix rear bracket L to front bracket L, and affix rear bracket R to front
bracket R. Secure them by applying M6 screws to the second screw hole
from the rear on the lower side and the second screw hole from the rear on
the upper side. (See Section G-G.)
`
Secure the table in position while fully pressing rear brackets L and R against the
rack posts (in the direction of arrow A).
`
Secure the table in position while fully pressing rear bracket L against front
bracket L and rear bracket R to front bracket R so that no gaps appear (in the
directions of arrows B and C).
`
If you are unable to press against rear brackets L and R adequately, do so after
slightly loosening the M6 screws marked with an asterisk (*).
`
The table can be drawn out about 185 mm (until the screw holes for securing rear
brackets L and R are visible). Do not draw it out too much (see section G-G).
`
When mounting the table on a 19-inch rack other than the SE-RxRCxx, MC-
RxRCxx, and PW-RxRCxx, use screw holes for which the spacing of the M6
screws used to secure rear brackets L and R to front brackets L and R is
maximized.
4
Put away the table that was drawn out in step 2 and engage the simple
retainer mechanism of the slide rails.
Drawing out the table about 185 mm
* The same screw hole
䇭
positions on rear bracket L
䊁䊷䊑䊦
㪘
㪙
㪚
㪘
㪚
㪙
㪞
㪞
㪘
㪙
㪚
Section G-G
Second screw hole from
the rear on the lower side
Second screw hole from
the rear on the upper side
Rear side position
of table put away
M6 screws
M6 screws
Table
Table
Rear bracket R
Rear bracket R
Front bracket R
Rack post
Rack post
Front bracket R
Rear bracket L
Front bracket L
Rear bracket R
Front bracket R
Screw holes of rear bracket R
used to secure the table in position
Summary of Contents for 1740
