3
J
また、危害や損害の内容がどのようなものかを示すために、上記の絵表示と同時に次の記
号を使用しています。
■ 本文中の記号
本文中に記載されている記号には、次のような意味があります。
■ 製品の呼び方
本文中の製品名称を次のように略して表記します。
■ リサイクルについて
本製品を廃却する場合、弊社担当営業員に相談してください。本製品は産業廃棄物として
処理する必要があります。
各製品名は、各社の商標、または登録商標です。
各製品は、各社の著作物です。
All Rights Reserved, Copyright©
FUJITSU LIMITED 2008
△で示した記号は、警告・注意を促す内容であることを告げるもので
す。記号の中やその脇には、具体的な警告内容が示されています。
で示した記号は、してはいけない行為(禁止行為)であることを告
げるものです。記号の中やその脇には、具体的な禁止内容が示されて
います。
●で示した記号は、必ず従っていただく内容であることを告げるもの
です。記号の中やその脇には、具体的な指示内容が示されています。
記号
意味
お使いになる際の注意点や、してはいけないことを記述しています。
必ずお読みください。
ハードウェアやソフトウェアを正しく動作させるために必要なことが
書いてあります。必ずお読みください。
→
参照ページや参照マニュアルを示しています。
製品名称
本文中の表記
19
インチラック
モデル
1740
(
19R-174A1
、
19R-174B1
、
19R-174A2
、
19R-174B2
)
ラック、本製品
転倒防止用スタビライザ
スタビライザ
Summary of Contents for 1740
