Fujitsu 9379123037-02 Installation Insrtuctions Download

Page: 8 / 15

En-8

6.1. Wiring system diagram

•

Connection cable (to outdoor unit)

Control line

Power line

Earth (Ground) line

•

Wired remote controller cable

* Earth (Ground) the remote controller

(Please connect it when necessary.)

Red
White
Black

Indoor

unit side

CAUTION

Tighten the indoor unit connection cable and power supply indoor and outdoor unit,

terminal board connections

rmly with the terminal board screws. Faulty connection

may cause a

re.

If the indoor unit connection cable and power supply are wired incorrectly, the air

conditioner may be damaged.

Connect the indoor unit connection cable by matching the numbers of the outdoor and

indoor units terminal board numbers as shown in terminal label.

Earth (Ground) both the indoor and outdoor units by attaching an earth (ground) cable.

Unit shall be grounded in compliance with the country or region's regulations.

CAUTION

Be sure to refer to the above diagram for do correct

eld wiring. Wrong wiring causes

malfunction of the unit.

Check local electrical rules and also any speci

c wiring instructions or limitation.

6.2. Connection cable preparation

Keep the earth (ground) wire longer than the other wires.

Power supply cable
or connection cable

30 mm

40 mm or more

Earth (Ground) wire

• Use a 4-core wire cable.

6.3. Connection of wiring

CAUTION

• Use care not to mistake the power supply cable and connection wires when installing.

• Install so that the wires for the remote controller will not come in contact with other

connection wires.

(1) Remove the control box cover and install each connection wire.

Control box cover

Loosen the screws
(2 locations)

(2) After wiring is complete, secure the remote controller cable, connection cable, and

power supply cable with the cable clamps.

(3) Install the control box cover.

Cable clamp

Remote controller
cable

Connection cable
(to outdoor unit)

CAUTION

• Do not bundle the remote controller cable, or wire the remote controller cable in

parallel, with the indoor unit connection wire (to the outdoor unit) and the power
supply cable. It may cause erroneous operation.

9379123037-02.indb 8

7/4/12 3:47 PM

Summary of Contents for 9379123037-02
















Search results

Summary of Contents for 9379123037-02

Reviews:

Related manuals for 9379123037-02

Brands by name

Popular brands

Fujitsu 9379123037-02, Installation Insrtuctions

Search results

Summary of Contents for 9379123037-02

Reviews:

Related manuals for 9379123037-02

Brands by name

Popular brands