background image

En-9

ADJUSTING THE DIRECTION OF AIR CIRCULATION

SWING OPERATION

Begin air conditioner operation before performing this procedure.

To se

l

ect SWING Ope

r

at

i

o

n

P

r

ess t

h

e SWING 

bu

tto

n

The SWING Display will light.
In this mode, the Air Flow Direction Louvers will swing automatically to direct the air 
 ow both up and down.

To stop SWING Ope

r

at

i

o

n

P

r

ess t

h

e SWING 

bu

tto

n

 o

n

ce a

g

a

in.

The SWING Display will go out.
Air ow direction will return to the setting before swing was begun.

  Attempting to move up/down air direc-

tion flaps manually could result in im-
proper operation; in this case, stop op-
eration and restart. The louvers should 
begin to operate properly again.

  When used in a room with infants, chil-

dren, elderly or sick persons, the air 
direction and room temperature should 
be considered carefully when making 
settings.

Ve

r

t

i

ca

l

 A

ir

 D

ir

ect

i

o

n

 A

d

j

u

stme

n

t

P

r

ess t

h

e SET 

bu

tto

n

 (Ve

r

t

i

ca

l

)

.

Each time the button is pressed, the air direction range will change as follows:

1

 

 

2

 

 

3

 

 

4

The remote controller’s display 
does not change.

I

n

st

ru

ct

i

o

n

r

e

l

at

ing

 to 

h

eat

ing

 (*) a

r

e app

li

ca

bl

e o

nl

y to “HEAT & COOL MODEL” (Re

v

e

r

se Cyc

l

e)

.

Begin air conditioner operation before performing this procedure.

Air Flow Direction Setting:

1

2

3

4

:  During Cooling/Heating/Dry mode

 The vertical air ow direction is set automatically as shown, in accordance with the 

type of operation selected.

 

During Cooling/Dry mode 

:  Horizontal  ow 

1

*  During Heating mode 

:  Downward  ow 

4

 During AUTO mode operation, for the  rst minute after beginning operation, air ow 

will be horizontal 

1

; the air direction cannot be adjusted during this period.

Ho

ri

zo

n

ta

l

 A

ir

 D

ir

ect

i

o

n

 A

d

j

u

stme

n

t

The function cannot be used.

A

b

o

u

t S

wing

 Ope

r

at

i

o

n

T

h

e type o

f

 ope

r

at

i

o

n

Ra

ng

e o

f

 s

wing

Cooling/Heating/Dry/Fan

1

 to 

4

 The SWING operation may stop temporarily when the air 

conditioner’s fan is not operating, or when operating at very 
low speeds

9374379453_OM_EN.indd   9

12/3/2010   4:31:06 PM

Summary of Contents for AIR CONDITIONER





















Reviews: