manualshive.com logo in svg

Fujitsu Eternus DX410 S2, Cli User'S Manual

The Fujitsu Eternus DX410 S2 comes equipped with cutting-edge technology for data storage solutions. Easily navigate its advanced features with the comprehensive Cli User's Manual, available for free download from our website. Obtain optimal functionality and unleash the full potential of this remarkable product by referring to the user manual.

Share
Download
background image

Chapter 3  Configuration Settings and Display
  3.5  Host Interface Management  >  show host-lu-qos-performance

ETERNUS CLI User’s Guide

Copyright 2015 FUJITSU LIMITED

P2X0-1030-09ENZ0

353

■

Example(s)

V:

Maximum number of I/Os per second for a LUN

W:

Average transfer amount per second for a LUN (in MB/s)

X:

Minimum transfer amount per second for a LUN (in MB/s)

Y:

Maximum transfer amount per second for a LUN (in MB/s)

Z:

Accumulated delay time since the start of a command from the QoS control of a LUN (in milliseconds)
"Overflow" is displayed when a long time passes from the start of performance measurement to the end of
performance measurement and the accumulated delay time exceeds the limit.

a:

Average delay time for a single command from the QoS control of a LUN (in milliseconds)

When the port type that is described above is iSCSI and a host without an IP address is specified, 
performance measurement information is obtained from multiple IP address. When an IP address is not 
specified, "J: Host IP address" shows the actual IP address of the host that is logged in to the ETERNUS Disk 
storage system.

The following example displays the performance measurement information when no parameters are set. For
CM#1 CA#0 Port#0, Delay Total Time exceeds the limit and "Overflow" is displayed:

CLI> show host-lu-qos-performance
Port                    IOPS                             Throughput(MB/s)               Delay Time(ms)
                        Ave        Min        Max        Ave        Min        Max      Total        Ave
CM#0 CA#0 Port#0        100         10        100          2          1          3         20         10
CM#0 CA#0 Port#1         10          1         30         10          2        100        120         10
CM#1 CA#0 Port#0         10          1         30         10          2        100   Overflow         10

The following example displays the performance measurement information when a host interface port with
the host affinity mode enabled is set:

CLI> show host-lu-qos-performance -port 000
CM#0 CA#0 Port#0 Port Performance Information
 Port Type               FC
 Host Affinity           Enable
 Performance Monitoring  ON
 Monitoring Start Time   2012-04-11 12:00:00
 Monitoring Stop Time    2012-04-11 12:05:00

                             IOPS                             Throughput(MB/s)               Delay Time(ms)
                             Ave        Min        Max        Ave        Min        Max      Total        Ave
Port Total                   100          1        100          2          1        100       1000         10

Host                         IOPS                             Throughput(MB/s)               Delay Time(ms)
No.  Name                    Ave        Min        Max        Ave        Min        Max      Total        Ave
   0 Host#FC_0               100         10        100          2          1          3         20         10
   1 Host#FC_1                10          1         30         10          2        100        120         10

Summary of Contents for Eternus DX410 S2





















































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Eternus DX410 S2

N-Tron 700 Series User Manual & Installation Manual preview
700 Series
Brand: N-Tron Pages: 101
Cabletron Systems SmartSTACK ELS100-24TXG Installation And User Manual preview
SmartSTACK ELS100-24TXG
Brand: Cabletron Systems Pages: 112
Cabletron Systems ESX-1380 Management Manual preview
ESX-1380
Brand: Cabletron Systems Pages: 86
Cabletron Systems CSX200 CyberSWITCH Setup Manual preview
CSX200 CyberSWITCH
Brand: Cabletron Systems Pages: 2
Cabletron Systems MicroMMAC 22ES Installation Manual preview
MicroMMAC 22ES
Brand: Cabletron Systems Pages: 93
D-Link DIR-853/EE Quick Installation Manual preview
DIR-853/EE
Brand: D-Link Pages: 83
Western Digital WD Caviar Green WD10EADS Specification Sheet preview
WD Caviar Green WD10EADS
Brand: Western Digital Pages: 2
Hirschmann OCTOPUS 5TX-EEC Description And Operating Instructions preview
OCTOPUS 5TX-EEC
Brand: Hirschmann Pages: 6
QNAP TS-464U User Manual preview
TS-464U
Brand: QNAP Pages: 69
AIC J4078-01 User Manual preview
J4078-01
Brand: AIC Pages: 112
WolfPack 18x18 Card Cage User Manual preview
18x18 Card Cage
Brand: WolfPack Pages: 31
IBM EXN4000 Installation And Setup Instructions preview
EXN4000
Brand: IBM Pages: 18
Maipu SM3100-28TC-AC Install Manual preview
SM3100-28TC-AC
Brand: Maipu Pages: 19
H3C UniServer R2900 G3 Installation, Quick Start preview
UniServer R2900 G3
Brand: H3C Pages: 15
Supermicro SSG-2029P-ACR24H User Manual preview
SSG-2029P-ACR24H
Brand: Supermicro Pages: 136
Drobo DroboElite User Manual preview
DroboElite
Brand: Drobo Pages: 178
Supero SUPERSERVER 6035B-8R+ User Manual preview
SUPERSERVER 6035B-8R+
Brand: Supero Pages: 110
ADDON ARM8100 Quick Installation Manual preview
ARM8100
Brand: ADDON Pages: 4

Brands by name

Popular brands

Load more brands