manualshive.com logo in svg

Fujitsu Fujitsu fi-5950, Operator'S Manual

The Fujitsu Fujitsu fi-5950 is a high-performance document scanner designed to streamline your paper-intensive workflows. With its advanced features and industry-leading performance, it ensures optimal efficiency and productivity. Download the comprehensive brochure & specs manual for free from 88.208.23.73:8080 to unlock the full potential of this top-notch scanner.

Share
Download
background image

208

8.16 Thin Paper Mode

8.16 Thin Paper Mode

If nonstandard thin paper cannot be fed and scanned smoothly, use this mode.
In this mode, sheets of paper are fed at a slower speed so that thin paper can be fed and scanned properly. 

Follow the steps below to switch to the Thin Mode.

1.

Start up the Software Operation Panel.

Refer to 

“8.1 Scanner Settings” on page 173

.

2.

Select [Device Setting 2] from left side list in the window, and select [Thin 
Paper Mode] from its lower level.

3.

Select one of the following option.   

Disable

: For the document described in the Document specification.

Thin paper mode

: For the thin document than described in the Document specification.

Super-thin paper 
mode

: For very thin document rather than the Thin paper above.

ATTENTION

 In Thin Paper Mode, the document is scanned at a lower speed, and thus it 
takes longer.
 This mode should be used only for thin paper. Set the setting to “Disable” 
while you use paper of standard thickness.
 About the paper thickness, refer to 

“7.2 Document Quality” on page 159

.

Summary of Contents for Fujitsu fi-5950


































































































































































































































































Reviews:

No comments

Related manuals for Fujitsu fi-5950

Canon ImageFormula DR-7080C Specification preview
ImageFormula DR-7080C
Brand: Canon Pages: 4
Barco F35 Quick Start Manual preview
F35
Brand: Barco Pages: 2
Rangemaster 900 SCAN User Manual preview
900 SCAN
Brand: Rangemaster Pages: 2
Kodak 8738056 - Scan Station 500 User Manual preview
8738056 - Scan Station 500
Brand: Kodak Pages: 43
Canon CanoScan LiDE 120 Online Manual preview
CanoScan LiDE 120
Brand: Canon Pages: 245
Genius SLIM 1200U2 User Manual preview
SLIM 1200U2
Brand: Genius Pages: 30
Genius ColorPage HR8 User Manual preview
ColorPage HR8
Brand: Genius Pages: 37
VDO TPMS Pro Instructions Manual preview
TPMS Pro
Brand: VDO Pages: 6
C-Pen Connect BT10 Quick Start Manual preview
Connect BT10
Brand: C-Pen Pages: 13
Zircon MultiScanner i520 OneStep User Manual preview
MultiScanner i520 OneStep
Brand: Zircon Pages: 8
Rangevision Smart Manual preview
Smart
Brand: Rangevision Pages: 31
Kaixin W1 User Manual preview
W1
Brand: Kaixin Pages: 33
Jireh Skoot Manual preview
Skoot
Brand: Jireh Pages: 154
Leica Geosystems ScanStation P30 Quick Manual preview
ScanStation P30
Brand: Leica Geosystems Pages: 12
Hasselblad Flextight X1 User Manual preview
Flextight X1
Brand: Hasselblad Pages: 183
Paracosm PX-80 Field Manual preview
PX-80
Brand: Paracosm Pages: 78
PageExpress A620 User Manual preview
A620
Brand: PageExpress Pages: 16
UKGpro TimeBase Installation Manual preview
TimeBase
Brand: UKGpro Pages: 7

Brands by name

Popular brands

Load more brands