Fujitsu Fujitsu fi-5950 Operator'S Manual Download | Manualshive

Page: 46 / 257

background image

26

2.7 Setting up the Stacker

3.

Move your hands away from the stacker slowly.

⇒

The stacker will be fixed in a horizontal position.

<Changing Stacker table motion>

Thin paper sometimes curles when it is ejected to the stacker. This method may be effective to improve the
stacking capability by fixing the stacker hight in the appropriate position.

1.

Close the scanner driver dialog box if it is displayed on the PC monitor.

2.

Press both Hopper Height buttons on operator panel (

and

) for

more than 2 seconds.

⇒

Every time this is done, the stacker table moves between the lowest position and the

position little a bit above. Set the stacker table at the position little a bit above the lowest

position.

HINT

•

When set to the “bottom edge alignment” position, the stacker will automat-

ically adjust its height according to its load.

•

When set to the “Bottom edge alignment” position, the stacker’s maximum

load will be 500 sheets.

ATTENTION

•

On both sides walls of the stacker, photo sensors are installed to detect

document height on the stacker. Make sure these sensors are not
blocked.

•

The stacker may move up or down when the scanner is in the ready sta-

tus up or when scanning starts. Do not touch the stacker or place any-
thing on it at those times.

Send t

o

Powe

r

Thin

Photo sensors

«
...
44
45
46
47
48
...
»

Summary of Contents for Fujitsu fi-5950


































































































































































































































































Reviews:

No comments

Related manuals for Fujitsu fi-5950

Brand: Youkey Pages: 83

Brand: Leuze Pages: 15

Brand: Microtek Pages: 8

Brand: U-Line Pages: 3

Brand: Banner Pages: 80

Brand: Faro Pages: 58

USB Color Flat Bed Scanner

Brand: Medion Pages: 24

Brand: Medion Pages: 28

FreeScan UE Pro

Brand: Shining 3D Pages: 54

Brand: Pyle Pages: 14

Brand: Nikon Pages: 72

Brand: Raven Pages: 34

Brand: POSIFLEX Pages: 16

Brand: Kodak Pages: 51

Brand: Uniden Pages: 44

Brand: Avision Pages: 42

imageFORMULA DR-1210C

Brand: Canon Pages: 32

ROAD-SCANNER Compact

Brand: Siteco Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands