background image

87

W I r e l e s s   L A N   U s e r ’ s   G u i d e  

 WIRELESS NETWORK CONSIDERATIONS

The WLAN device supports IEEE802.11a/b/g and 
operates in the 2.4GHz ISM band and the 5 GHz UNII 
bands.

The maximum range of the WLAN device indoors is 
typically 80 feet (25 meters). Please note that the max-
imum range you achieve may be shorter or longer than 
80 feet, depending on factors such as access point 
transmit power, number and density of obstructions, 
or external RF interference.

Microwave ovens will interfere with the operation of 
WLAN device as microwave ovens operate in the same 
2.4GHz frequency range that IEEE802.11b/g devices 
operate in. Interference by microwaves does not occur 
with IEEE802.11a radio which operates in the 5 GHz 
RF band.

Wireless devices that transmit in the 2.4GHz fre-
quency range may interfere with the operation of 
WLAN devices in IEEE802.11b/g modes. Symptoms of 
interference include reduced throughput, intermittent 
disconnects, and large amounts of frame errors. It is 
HIGHLY recommended that these interfering devices 
be powered off to ensure the proper operation of the 
WLAN device.

DEACTIVATING THE WLAN DEVICE

Deactivation using the Wireless On/Off Switch

The WLAN device can be deactivated quickly and effi-
ciently by toggling the Wireless On/Off Switch to the Off 
position. 

(Figure A-3) 

The wireless On/Off switch has no 

effect on non-Wireless LAN models.

Deactivation using Intel PROSet for Wireless Utility

The WLAN device can be deactivated in Windows using 
the Intel PROSet for Wireless utility. The procedure to 
accomplish this:

1.

Click [Start]-> [All Programs].

2.

Select Intel ProSet Wireless, then click on Intel 
ProSet Wireless from the menu that appears. The 
Intel ProSet Wireless utility will be displayed.

3.

At the bottom left corner of the window, select 
Wireless Off from the dropdown list.

ACTIVATING THE WLAN DEVICE

Activation of the WLAN device can be accomplished 
using the same methods as the deactivation process

Using the Wireless On/Off Switch

In Windows using the Intel PROSet for Wireless utility

Figure A-3. Wireless LAN On/Off Switch Location

Figure A-2. Access Point (Infrastructure) Mode Network

ADSL modem,
cable modem,
or similar

Internet

Wired LAN

Access Point*

Wireless LAN

*An optional hub for a wired
LAN may be required depending
upon the type of access point used.

N6210.book  Page 87  Wednesday, May 18, 2005  10:24 AM

Summary of Contents for Lifebook N6210









































































































































Reviews: