background image

181

PRIMERGY RX100 S3 User’s Guide    

Inst
allin
g I

nte

rn

al O

pti

ons

7

7.3 Installing Memory Modules

Additional memory will help to increase the amount of data to read at a time and 

improve the server processing capability.

• Before installation or removal, turn off the server and all peripheral devices.            

Also unplug all power cables from the server. Failure to do so may cause             

electric shock (

"1.4.3 Turning Off the Server" (pg.33)).

• Do not install unauthorized third party memory modules. Doing so may cause           

electric shock, a fire, or failures.

• Wait for a sufficient period of time after server shutdown before installing or            

removing memory. Failure to do so may cause burns.

• When  installing  or  removing  memory  modules,  make  sure  to  remove  the          

screws on the specified points only. Failure to do so may cause injury.

Also, it may cause failures.

• Touch only the specified part of the printed circuit board.

Failure to do so may cause injury. Also, it may cause failures.

• The circuit boards and soldered parts of internal options are exposed. They           

can be damaged by static electricity.

Before handling them, first touch a metal part of the server to discharge static             

electricity.

• Do not insert or remove memory modules repeatedly. This could damage the           

server.

• Hold the edge of the memory module as shown below. Do not touch the parts              

containing gold wire (terminal).

 

Do not touch this part

Memory module

Summary of Contents for Primergy RX100 S3
































































































































































































































































































Reviews: