background image

RX4770 M2

Operating Manual

69

Starting up and operation

2

Global Error indicator (yellow)

Lights up yellow

 if a prefailure event has been detected that 

requires (precautionary) service intervention. 

Flashes yellow

 if an error was detected that requires service 

intervention.

Does not light up

 if there is no critical event.

If the event is still acute after a power failure, the indicator is activated 
after the restart.

The indicator also lights up in standby mode.

You can find more details on the indicated errors in the System Event 
Log (SEL), on the ServerView Local Service Display, in the ServerView 
Operations Manager or via the iRMC's Web interface.

3

ID indicator (blue)

Lights up blue

 when the system has been selected by pressing the ID 

button. To deactivate, press the button again.

The ID indicator can also be activated via the ServerView Operations 
Manager and the iRMC Web interface and its status reported to the 
ServerView Operations Manager and the iRMC.

Flashes blue

 when the server has been highlighted using IRMC (AVR) 

when local VGA off for easy identification.

4

ID button

Summary of Contents for PRIMERGY RX4770 M2





















































































Reviews: