manualshive.com logo in svg

Fujitsu ScanSnap N1800, Operator'S Manual

The Fujitsu ScanSnap N1800 is a cutting-edge document scanner that revolutionizes the way you handle paperwork. With its intuitive design and advanced features, this device offers unbeatable convenience and efficiency. To make the most of its capabilities, don't forget to download the Software Manual for this product, absolutely free, from 88.208.23.73:8080.

Share
Download
background image

451

8.2.2 Other Network Connection Troubleshooting

There are many reasons why a network connection may not be possible.
The following section provides information about general troubles that may occur when 
connecting to a network.
If the cause of the problem is unknown or the problem persists, check the items in 

"8.4 

Points to Check before Contacting Your FUJITSU Scanner Dealer" (page 467)

 and 

contact your FUJITSU scanner dealer or an authorized FUJITSU scanner service 
provider.

■ 

Failure to Connect to a Server Using Its IP Address

If a server cannot be connected to by using its IP address, and does not respond to a ping 
test, try the following steps:

■

Action

Check that the LAN cable has been attached to both the scanner and server correctly.
If the server is connected using a LAN cable (straight type), in case Auto MDI/MDI-X (automatic 
selection) is not supported, a LAN cable (crossover type), switch, or router is required between 
the scanner and server.
If this is not the case, the LAN cable may be faulty. Find a LAN cable that functions normally and 
try again.

■

Action

On the [IP Address] window, check that the IP address or subnet mask settings are correct.
For more details about the [IP Address] window, refer to 

"4.8.1 Giving the Scanner an IP 

Address" (page 113)

.

■

Action

If using DHCP, on the [Network Status] window, check that IP address, subnet mask, and default 
gateway settings are all correct.
If these settings are not correct, the DHCP server may not operate normally, or the DHCP server 
may not assign valid IP addresses because of restricted number of leases or MAC address 
validation.
Check the DHCP server connection status and the details of the server settings.
For more details about the [Network Status] window, refer to 

"4.8.7 Checking the Network 

Operating Status" (page 121)

.

Connection error between a server and the scanner, or problem with the 
LAN cable.

IP address or subnet mask is invalid.

When using DHCP, the DHCP server does not operate normally, or there 
is a problem with the DHCP server settings.

Summary of Contents for ScanSnap N1800
































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ScanSnap N1800

Oemtools 24936 Operating Instructions And Parts Manual preview
24936
Brand: Oemtools Pages: 4
unGer nLite HydroPower HP12 Series Installation & Operating Instruction preview
nLite HydroPower HP12 Series
Brand: unGer Pages: 16
Pro-Cut GYR Quick Start Manual preview
GYR
Brand: Pro-Cut Pages: 24
CEMO KS-Mobil Easy 120l Operating Instructions Manual preview
KS-Mobil Easy 120l
Brand: CEMO Pages: 112
Pitsco Education Electric Energy Prop Racer User Manual preview
Electric Energy Prop Racer
Brand: Pitsco Education Pages: 4
Heathkit HD-10 Manual preview
HD-10
Brand: Heathkit Pages: 8
Braillo 650 SW User Manual preview
650 SW
Brand: Braillo Pages: 127
M-B MSV3 Operation Manual preview
MSV3
Brand: M-B Pages: 49
Automatic Systems TR490 Installation Manual preview
TR490
Brand: Automatic Systems Pages: 16
Deer Fence Access Gate Installation Instructions preview
Access Gate
Brand: Deer Fence Pages: 5
3M 803 Owner'S Manual preview
803
Brand: 3M Pages: 23
KEUCO 17612 01 9002 Installation And Operating Instructions Manual preview
17612 01 9002
Brand: KEUCO Pages: 18
CAMDEN CX-33 Installation Instructions Manual preview
CX-33
Brand: CAMDEN Pages: 28
LAUNCH TECH X-431 PRO V4.0 User Manual preview
X-431 PRO V4.0
Brand: LAUNCH TECH Pages: 96
Lascar EL-USB-RT Installation And Operation Manual preview
EL-USB-RT
Brand: Lascar Pages: 8
B+B Sensors LogBox AA IP65 Instruction Manual preview
LogBox AA IP65
Brand: B+B Sensors Pages: 25
WEG DWB160 Manual preview
DWB160
Brand: WEG Pages: 2
Würth 0891 703 140 Translation Of The Original Operating Instructions preview
0891 703 140
Brand: Würth Pages: 83

Brands by name

Popular brands

Load more brands