Chapter 11
XSCF Unit Replacement
11-11
Confirm that the currently active XSCF is the XSCF unit for which you executed
the
replacefru
command at the start.
iii. After confirming that the XSCF units are not switched over, execute the
replacefru
command again.
(a)When you can execute the
replacefru
command
Follow the
replacefru
command to replace the unit.
(b)In case communication with XSCF is lost after you physically replaced the target
XSCF
The new XSCF unit is physically mounted; however, the mounting process is not
yet finished completely. When the
replacefru
command showed a message
which prompts the replacement of XSCF unit, once extract the inserted XSCF unit
which has undergone the replacement, and then reinsert it.
Note –
If an attempt to re-execute the
replacefru
command from the active XSCF unit
fails, or if an XSCF failover occurred and the XSCF units switched, both XSCF units will
require cold replacement. For information on cold replacement, see
.
11. Confirm that the replacement components are normal by using the
showhardconf
or
showstatus
command of XSCF.
Unless "*" is displayed for the replacement XSCFU, it is operating normally.
For details of the
showhardconf
command and
showstatus
command, see the
SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers XSCF User’s Guide
, the
SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers XSCF Reference
Manual
, or the man page.
Note –
The
showstatus
command displays information on degraded components.
12. Confirm that the version of the replaced XSCF unit is the same. If the version
number is different, upgrade the firmware again to match up the version numbers.
For the version matching of firmware, see the
SPARC Enterprise
M3000/M4000/M5000/M8000/M9000 Servers XSCF User’s Guide
.
13. Close the door on the server, and lock it.
Summary of Contents for SPARC Enterprise M8000
