Fujitsu UTY-RVN*M Operating Manual Download

Page: 25 / 25

En-24

8-2. Troubleshooting

WARNING

In the event of a malfunction (burning smell, etc.), immediately stop operation, turn off the electrical breaker and consult

authorized service personnel.

Merely turning off the unit’s power switch will not completely disconnect the unit from the power source. Always be sure to turn

off the electrical breaker to ensure that power is completely off.

Before requesting service, perform the following checks:

Symptom

Items to check

See

Page

CHECK ONCE

Does not operate at all:

• Has the circuit breaker been turned off?
• Has there been a power failure?
• Has a fuse blown out, or a circuit breaker been tripped?

─

Is the timer operating?

─

Is key lock enabled?

Following functions

cannot be set:

•Economy

•Set temp. auto return

• Set temp. range limita

tion

•On timer

•Off timer

•Weekly timer

•Auto-off timer

If the function you are selecting is restricted by [Management] function,

following message is displayed in the operation guidance display.

XXXXXX

Restricted by the management function

Back:

Has the function setting been set to [Enable] or [On]?

─

On timer or Off timer

does not work:

Has there been a power outage? Any power outage cancels the On or

Off timer.

After the power supply is resumed, set the [Enable/Disable setting] to

[Enable] again.

11, 12

Operation is automati-

cally stopped:

Has off timer been set?

Has weekly timer been set?

Has auto-off timer been set?

Operation does not

stopped even if auto-off

timer has been set:

Has the operation been started by pressing the [On/Off button] on this

remote controller?

Has the operation been started by weekly timer or on timer?

Has the weekly timer been on during the counting down of the Auto-off

timer?

Has it been within the valid hour?

Has there been a power outage? Any power outage cancels the Auto-off

timer.

─

Is message [R.C. prohition (All, on/off)] and

icon displayed?

Set temperature is

changed automatically:

Has set temp. auto return been set?

Does not return to the set

temperature:

Has set temp. range limitation been set?

Set temperature cannot

be changed:

Has set temp. range limitation been set?

Is message [R.C. prohition (Set temp. all)] and

icon displayed?

NORMAL

FUNCTION

Airflow is stopped and

is displayed on the

icon display of the “Moni-

tor” screen:

Airflow is stopped due to the automatic defrosting, oil recovery, or

mode mismatch. Refer to the operating manual of the relevant indoor

unit.

─

9380221043_OM.indb 24

8/22/2012 3:55:02 PM

Summary of Contents for UTY-RVN*M


























Search results

Summary of Contents for UTY-RVN*M

Reviews:

Related manuals for UTY-RVN*M

Brands by name

Popular brands

Fujitsu UTY-RVN*M, Operating Manual

Search results

Summary of Contents for UTY-RVN*M

Reviews:

Related manuals for UTY-RVN*M

Brands by name

Popular brands