background image

XG Series User's Guide

Chapter 5 Command Reference

Device Information Settings

317

5.15.8.21 serverinfo ssh ip6

Function

Set the IPv6 SSH login server function

Available Model

XG0224 / XG0448 / XG0440DC / XG0440DCR / XG2600

Syntax

serverinfo ssh ip6 <mode>

Options

<mode>

on
Enable IPv6 SSH login server function

off
Disable IPv6 SSH login server function

Use Mode

Configuration mode (admin class)

Explanation

Set whether or not to enable the IPv6 SSH login server function.Setting this command
Off and the 

"serverinfo sftp ip6"

 command Off will reject a connection request using the 

IPv6 address from the ssh client. Setting this command Off and the 

"serverinfo sftp ip6"

 

command On will reject a connection request using the IPv6 address from the ssh client 
after the password was entered.

Caution

Enabling this command generates an SSH host authentication key at device power-on 
and execution of the 

"reset"

 command, and it takes several tens of seconds to several 

minutes for the processing time. ssh connection is enabled after the SSH host 
authentication key generation was completed.If this device has been started to enable 
this function while all the ssh and sftp functions were Off, it also takes several tens of 
seconds to several minutes for the processing time to generate an SSH host 
authentication key. Note that other processes may be affected; session monitoring 
timeout may occur, for example.

Default

It is assumed that the IPv6 SSH login server function is enabled.

serverinfo ssh ip6 on

Summary of Contents for XG0224
























































































































































































































































































































































































































































































































































































































































Reviews: