background image

XG700 User's Guide 

189/266

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 

5.15.16 show statistics vlan-traffic-counts 

Function 

Displays the traffic (the number of frames) of each VLAN after startup of the system hardware. 

Prompt 

xg> or xg# 

Command syntax 

show statistics vlan-traffic-counts

 

 

Command type 

Operation management command 

Output format 

xg# show statistics vlan-traffic-counts 
VLAN Traffic Statistics(Total Frame Counts)  2005/08/22-19:58:31
================================================================
[No.1]  

VID                  :  40 

  Rx-Frame  Counts   

 

: 0 

  Rx-NonUcast  Counts:  0 
[No.2]         
        
        

 

 

[No.]

 

Displays statistics of each VLAN.

 

 

VID

 

Displays the VID of the VLAN which has been set to collect its statistics. 

 

Specify the VLAN to collect its statistics using the "vlan-statistics collection" command. 

 

Rx-Frame Counts

 

Displays the cumulative count of frames which have been received at the specified VLAN (after the system startup), 
using a 10-digit, right-justified value.

 

 

Rx-NonUcast Counts

 

Displays the cumulative count of non-unicast frames which have been received at the specified VLAN (after the system 
startup), using a 10-digit, right-justified value. 

 

Summary of Contents for XG700 - Switch











































































































































































































































































Reviews: