manualshive.com logo in svg

Fujitsu XG700 - Switch, User Manual

The Fujitsu XG700 - Switch is a high-performance networking device equipped with advanced features. Ensure a seamless setup and optimal utilization by accessing our comprehensive User Manual. Available for free download at 88.208.23.73:8080, it provides clear instructions and valuable insights to maximize your experience with this cutting-edge switch.

Share
Download
background image

XG700 User's Guide 

90/266

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 

5.5.11 tftp put   

Function 

Uploads the files into the volatile memory to the TFTP server. 

Prompt 

xg# 

Command syntax 

tftp put HOST LOCAL-FILE [ REMOTE-FILE ] 

Parameter 

 

HOST 

Specify the hostname of the TFTP server or IP address.

 

IP addresses that can be specified are: 1.0.0.1 - 126.255.255.254, 128.0.0.1 - 191.255.255.254, and 192.0.0.1 - 
223.255.255.254. 

 

LOCAL-FILE 

Specifies a file name to upload. 

 

  [ REMOTE-FILE ] 

Specifies the file name to use when saving on the TFTP server.

 

When this parameter is omitted, it will be the same file name as "LOCAL-FILE." 

Command type 

Operation management commands 

Message 

% tftp: %1$: Host name lookup failure 

Explanation 

The specified hostname does not exist.

 

[[Inserted string]]%1$: specified hostname 

Solution 

Check whether the specified hostname is correct. 

% tftp: server says: %1$ 

Explanation 

An error has been received from the TFTP server.

 

[[Inserted string]]%1$: content of error message received from the TFTP server.

 

The content of message depend on the type of the TFTP server. For example, there is a message as below. 

− 

File not found: There are no files in the TFTP server. 

− 

Access violation: File permission error has occurred in the TFTP server. 

− 

Not allowed to overwrite existing files: The file in the TFTP server cannot be overwritten. 

− 

File already exists: There are files in the TFTP server. 

− 

Unknown transfer ID: Process will be aborted in time out. 

Solution 

Take actions in accordance with the message received from the TFTP server. 

% tftp: last timeout 

Explanation 

There is no response from the TFTP server. There is a possibility of network communication error with the 
management LAN, or the setting of time out of the TFTP server may be too short. 

Solution 

Check whether there is no problem in network connection with the TFTP server using the "ping" command. If the 
problem persists, review the setting of time out of the TFTP server. 

% local file: No such file or directory 

Explanation 

The specified file does not exist on the XG700.

 

[[Inserted string]]%1$: specified file name 

Solution 

Check the status of the file on the XG700. 

% Invalid IP-address. 

Explanation 

The specified format of the IP address or specified content is incorrect. 

Solution 

Specify the IP address in a correct format and execute it again. 

Note 

 

If there are no specified files in the TFTP server, or directories are specified, an error may occur. (it depends on the 
functionality of the TFTP server) 

 

When transferring a file with a large file size, if the time out is set short on the TFTP server, an error may occur. (it 
depends on the functionality of the TFTP server) 

 

In order to check whether the file has been transferred successfully, check that the file size displayed by the "dir" or "ls" 
command is identical to the size of the file transferred onto the TFTP server. 

Example 

Copy the content of running-config to the file name "run_conf."

 

Then, upload the copied "run_conf" file with the file name "run_conf_20050822" in the TFTP server called "host1." 

xg# show running-config > run_conf 
xg# tftp put host1 run_conf run_conf_20050822 

 

Summary of Contents for XG700 - Switch











































































































































































































































































Reviews:

No comments

Related manuals for XG700 - Switch

La Toulousaine 1400 Installation Manual preview
1400
Brand: La Toulousaine Pages: 6
D-Link DUB-H4 - Hub - USB Installation Manual preview
DUB-H4 - Hub - USB
Brand: D-Link Pages: 4
D-Link DSS-16+ Quick Install Manual preview
DSS-16+
Brand: D-Link Pages: 2
D-Link xStack DGS-3420 Series How To Set Up preview
xStack DGS-3420 Series
Brand: D-Link Pages: 2
D-Link DXS-3600-32S Quick Installation Manual preview
DXS-3600-32S
Brand: D-Link Pages: 29
D-Link DWS-1008 User Manual preview
DWS-1008
Brand: D-Link Pages: 454
D-Link DWS-1008 Product Manual preview
DWS-1008
Brand: D-Link Pages: 502
D-Link DGS-3312SR Product Manual preview
DGS-3312SR
Brand: D-Link Pages: 244
D-Link GO-SW-5G User Manual preview
GO-SW-5G
Brand: D-Link Pages: 20
D-Link DES-1008E Quick Install Manual preview
DES-1008E
Brand: D-Link Pages: 2
D-Link KVM-440 User Manual preview
KVM-440
Brand: D-Link Pages: 37
D-Link DES-1018DG Quick Installation Manual preview
DES-1018DG
Brand: D-Link Pages: 28
3Com Switch 4500 Family Datasheet preview
Switch 4500 Family
Brand: 3Com Pages: 16
3Com PathBuilder S200 Series User Manual preview
PathBuilder S200 Series
Brand: 3Com Pages: 32
Eaton COOPER POWER SERIES Service Instructions Manual preview
COOPER POWER SERIES
Brand: Eaton Pages: 24
Eaton COOPER POWER SERIES Installation And Adjustment Instructions preview
COOPER POWER SERIES
Brand: Eaton Pages: 16
Eaton Crouse-hinds series Manual preview
Crouse-hinds series
Brand: Eaton Pages: 16
Eaton Cutler-Hammer AMPGARD Instructions preview
Cutler-Hammer AMPGARD
Brand: Eaton Pages: 4

Brands by name

Popular brands

Load more brands