FULBAT - www.fulbat.com
5
constant at the set value.
•
Analysis Mode (Battery retention test Mode)
- The charging is interrupted for a short period for battery voltage
measured.
- If the battery voltage falls too quickly, the battery is probably faulty.
-
The Yellow Charging LED is ON (if above situation occurred)
•
Float Mode (Safe voltage level of 13.6V)
- Full Green LED is ON.
- The Float Mode allows the charger to effectively be left connected
to your batteries; it works at a safe level of 13.6V, and ready for use.
•
Maintenance mode (Special pulse for long term maintenance)
- Full Charge Green LED is ON.
- The program engages a special charging waveform and monitors
the battery voltage variety, if the battery voltage sinks, the special
pulses will keep the battery in optimal state, if the battery voltage
drops even lower, the battery charger will switch into Bulk charging
stage.
- The maintenance mode allows the charger can be connected to
the battery over the course of a season; if possible; check the
electrolyte liquid level in the battery.
LED STATUS INIDICATOR TABLE
LED
Status
Descriptions
Power / Fault LED - Green / Red
Green
On AC power is connected
Green Flash
ECO mode and no battery
presented
Red
On
Short –circuit or Reverse
polarity
Charge / Reconditioning
LED - Blue / Yellow
Blue
On
Bulk charge (C.C) mode /
Absorption charge (C.V)
mode
Blue
Flash Recondition / Soft start
Yellow
On Battery failure
Full Charge LED - Green
Green
On
The charger is at Float mode
(Full)
CHARGING CURVE (VOLTAGE)
CHARGING FEATURES
Voltage
(V)
Current
(A)
INITIAL
QUALIFICATION
Test automatically
battery condition
and determine if
charger engages
rejuvenation
or charging cycle.
REJUVENATION
Rejuvenates
sulphated
batteries with a
high frequency
pulse.
SOFT START
Increases
battery life by
gently starting to
charge the
battery.
BULK CHARGE
Reduces charging
time by delivering
maximum charge
to set voltage.
ABSORPTION
Ensures a full
charge to the
battery without
overcharging.
BATTERY TEST
Tests the battery
to ensure fully
charged.
FULLOAD 1500 - 8 STAGES
FLOAT
Float charge
maintains the
battery at
100% charge.
21 days restart.
LONG TERM
MAINTENANCE
If the battery
voltage sinks, the
special pulses
will keep the
battery in
optimal states.
CHARGING FEATURES
Voltage
(V)
Current
(A)
INITIAL
QUALIFICATION
Test automatically
battery condition
and determine if
charger engages
rejuvenation
or charging cycle.
REJUVENATION
Rejuvenates
sulphated
batteries with a
high frequency
pulse.
SOFT START
Increases
battery life by
gently starting to
charge the
battery.
BULK CHARGE
Reduces charging
time by delivering
maximum charge
to set voltage.
ABSORPTION
Ensures a full
charge to the
battery without
overcharging.
BATTERY TEST
Tests the battery
to ensure fully
charged.
FULLOAD F12 - 9 STAGES
EQUALIZATION
Returns a full
hydrometer
reading to
calcium batteries
by removing acid
stratification.
FLOAT
Float charge
maintains the
battery at
100% charge.
21 days restart.
LONG TERM
MAINTENANCE
If the battery
voltage sinks, the
special pulses
will keep the
battery in
optimal states.
CHARGING FEATURES
Voltage
(V)
Current
(A)
DESULPHATION
Recovers sulphated
batteries with a high
frequency pulse.
SOFT START
Increases battery life
by gently starting to
charge the battery.
BULK CHARGE
Reduces charging time
by delivering maximum
charge to set voltage.
ABSORPTION
Ensures a full charge
to the battery without
overcharging.
FLOAT
Float charge maintains
the battery at
100% charge.
FULLOAD 2000 - 5 STAGES
CARACTERISTIQUES DE CHARGE
Tension
(V)
Courant
(A)
TEST INITIAL
Teste la batterie
et détermine si
le chargeur lance
un programme de
récupération ou
de charge.
RECUPERATION
Récupération de
batteries
sulfatées grâce
à un cycle
d’impulsions à
fréquence élevée.
DEMARRAGE
LENT
Durée de vie de la
batterie
augmentée par
un démarrage en
douceur de
la charge.
CHARGE
PRINCIPALE
Délivre
automatiquement
un courant
constant adapté
aux
caractéristiques
de la batterie tout
en optimisant le
temps de charge.
ABSORPTION
Assure la charge
complète de la
batterie sans
risque de
surcharge.
TEST BATTERIE
Teste la batterie
pour s’assurer de
la pleine charge.
FULLOAD 1500 - 8 PHASES
MAINTENANCE
Assure le maintien
de la batterie
à 100% de
sa charge.
Automatique tous
les 21 jours.
MAINTENANCE
SUR LONG TERME
Si le voltage de la
batterie diminue
fortement, des
impulsions de
charge
maintiendront la
batterie en
conditions
optimales.
CARACTERISTIQUES DE CHARGE
Tension
(V)
Courant
(A)
TEST INITIAL
Teste la batterie
et détermine si
le chargeur lance
un programme de
récupération ou
de charge.
RECUPERATION
Récupération de
batteries
sulfatées grâce
à un cycle
d’impulsions à
fréquence élevée.
DEMARRAGE
LENT
Durée de vie de la
batterie
augmentée par
un démarrage en
douceur de
la charge.
CHARGE
PRINCIPALE
Délivre
automatiquement
un courant
constant adapté
aux
caractéristiques
de la batterie tout
en optimisant le
temps de charge.
ABSORPTION
Assure la charge
complète de la
batterie sans
risque de
surcharge.
TEST BATTERIE
Teste la batterie
pour s’assurer de
la pleine charge.
FULLOAD F12 - 9 PHASES
EGALISATION
Effectue une
charge
d’égalisation
pour équilibrer
les cellules de
la batterie, évitant
ainsi la
stratification de
l’électrolyte.
MAINTENANCE
Assure le maintien
de la batterie
à 100% de
sa charge.
Automatique tous
les 21 jours.
MAINTENANCE
SUR LONG TERME
Si le voltage de la
batterie diminue
fortement, des
impulsions de
charge
maintiendront la
batterie en
conditions
optimales.
CARACTERISTIQUES DE CHARGE
DOUTE
SUR LA COURBE
(2000)
Tension
(V)
Courant
(A)
RECUPERATION
Récupération de
batteries sulfatées
grâce à un cycle
d’impulsions à
fréquence élevée.
DEMARRAGE LENT
Durée de vie de la
batterie augmentée par
un démarrage en
douceur de la charge.
CHARGE PRINCIPALE
Délivre automatiquement
un courant constant
adapté aux
caractéristiques de la
batterie tout en
optimisant le temps
de charge.
ABSORPTION
Assure la charge
complète de la batterie
sans risque de
surcharge.
MAINTENANCE
Assure le maintien de la
batterie à 100% de sa
charge.
Automatique tous les
21 jours.
FULLOAD 2000 - 5 PHASES
CARACTERISTIQUES DE CHARGE
Tension
(V)
Courant
(A)
CHARGE
MAINTENANCE
FULLOAD 1000 - 3 PHASES
PULSE
CHARGING FEATURES
Tension
(V)
Courant
(A)
MAIN CHARGE
MAINTENANCE
FULLOAD 1000 - 3 STAGES
PULSE
CHARGING FEATURES
Tension
(V)
Courant
(A)
MAIN CHARGE
MAINTENANCE
FULLOAD 1000 - 3 STAGES
PULSE
TROUBLE SHOOTING
Types of
Problems
Indication
Possible
Causes
Suggested Solution
Charger
does not
work?
No Indicator
lights ON
-
No AC power
-
Check AC connections and
make sure Power Point is
switched ON
Charger
has no DC
output?
Fault LED
is ON
-
Output
is short
circuited
-
Reverse
polarity
connection
to Battery
-
Check DC connection between
charger and battery and
make sure they are not short
circuiting
-
Check that the crocodile clips
haven’t fallen off the battery
-
Check that the crocodile clips
/ ring terminals are connec-
ted to the correct polarity
No Charging
Current?
Fault LED
is ON
-
Battery is
severely
sulphated
-
Battery has
a damaged
cell
-
Overheat
protection
mode
-
Check the Battery condition,
age etc
-
Battery may need
replacement
-
Move battery & Charger to
cooler environment
Long char-
ging time,
Full light
does not
come on?
Fault LED
is ON
-
Battery
capacity too
large
-
Battery is
defective
-
Check the charger specifi
-
cation matches the battery
capacity
-
Battery cannot be charged
and must be replaced
MAINTENANCE
The charger is maintenance free. If the power cord is damaged, the
charger must be left to the reseller for maintenance. The case should
be cleaned occasionally. The charger should be disconnected from the
power while cleaning.
