background image

9

AIR COMPRESSOR SAFETY WARNINGS (cont.)

¥  Pull the ring on the safety valve daily to ensure that it operating properly and to clear any 

possible debris from the outlet.

¥  Keep the compressor at least 300mm from the nearest wall to ensure adequate 

ventilation for cooling purposes.

¥  Before transporting the compressor make sure that the pressurised air is bled from the 

tank and that the compressor is firmly secured.

¥  Protect the air hose and cordset from damage. Inspect for weak or worn spots regularly 

and replace if necessary.

¥  Avoid using an extension cord with this product. Use additional air hose instead of an 

extension cord to prevent power loss and possible damage to the motor. 

¥  After long working periods external metal parts could be hot.

¥  Always press the on/off button down to switch off the compressor before switching off 

the power or removing the power plug.

¥  After using the compressor, switch off the on/off button, disconnect the power supply 

and open the outlet valve to release the pressure.

¥  Never attempt to remove any part of the compressor whilst the tank is under pressure.

Wear goggles, wear earmuffs, wear a breathing mask

Never apply the outlet air of this compressor directly on to any part of a persons body. Do 

not attempt to block the air outlet with your finger or any part of your body.
The tool must be used only for its prescribed purpose. Any use other than those mentioned 

in this Manual will be considered a case of misuse. The user and not the manufacturer shall 

be liable for any damage or injury resulting from such cases of misuse.
The manufacturer shall not be liable for any changes made to the tool nor for any damage 

resulting from such changes.
Even when the tool is used as prescribed it is not possible to eliminate all residual risk 

factors. The following hazards may arise in connection with the tools construction and 

design:
¥  Damage to the lungs if an effective breathing mask is not worn.

¥  Damage to hearing if effective earmuffs are not worn.

¥  Damage to the eyes if effective safety goggles or shield are not worn.

WARNING!

 In the event that an air line is cut or broken, the air supply must be turned 

off at the compressor. A broken air line which is not supported is extremely dangerous 

and can whip around very quickly, both with the capability of striking people, and 

blowing foreign particles into the air.
Do not attempt to catch the air line but immediately keep bystanders well clear and 

turn off the air supply to the hose, turn off the compressor at the On / Off button, 

and then remove the hose from the compressor.

Summary of Contents for FBACVT-5030





















Reviews: