background image

16

WARRANTY EXCLUSIONS

The following actions will result in the warranty being void.

If the tool has been operated on a supply voltage other than that specified on the tool.

• 

If the tool shows signs of damage or defects caused by or resulting from abuse, accidents 

• 

or alterations.
Failure to perform maintenance as set out within the instruction manual.

• 

If the tool is disassembled or tampered with in any way.
The warranty excludes damage resulting from product misuse or product neglect.

• 
• 

This warranty is given by Ozito Industries Pty Ltd. 
ABN: 17 050 731 756
Ph.1800 069 486

Australia/New Zealand (Head Office)

1-23 Letcon Drive, Bangholme, Victoria, Australia 3175

FB1

WARRANTY

TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER AND DATE OF 

PURCHASE AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE WILL TAKE YOUR CALL 

AND ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE WARRANTY POLICY 

OR PROCEDURE.

The benefits provided under this warranty are in addition to other rights and remedies which

are available to you under law. The warranty covers manufacturer defects in materials, 

workmanship and finish under normal use.  

1 YEAR WARRANTY

Your product is guaranteed for a period of 

12 months from the original date of purchase

.

If a product is defective it will be repaired in accordance with the terms of this warranty.

Warranty excludes consumable parts, for example: wheels, bearings.

Our goods come with guarantees that cannot be excluded under Australian Consumer law & 

Consumer Guarantees Act 1993 (NZ). You are entitled to a replacement or refund for a major 

failure and to compensation for other reasonably foreseeable loss or damage. You are also 

entitled to have the goods repaired and replaced if the goods fail to be of acceptable quality 

and the failure does not amount to a major failure.  

`

Australia 1800 069 486

New Zealand 0508 069 486

YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER TO MAKE A 

CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST 

BUNNINGS WAREHOUSE (see www.bunnings.com.au or www.bunnings.co.nz for store locations) 

WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO RETURNING YOUR PRODUCT FOR 

WARRANTY PLEASE TELEPHONE OUR CUSTOMER SERVICE HELPLINE:   

Summary of Contents for FBT-0500

















Reviews: