background image

                                                                                                                                                     

User’s Manual   

For

 

 

MD2278 

High Performance Microstepping Driver

 

Version 1.0 

©2000 All Rights Reserved

 

 

Attention: Please read this manual carefully before using driver!

 

 

 

 

 

 

                                                                                                                                                     

The

 

content in this manual has been carefully prepared and is believed to be accurate, but no 

responsibility is assumed for inaccuracies. 
 

FULLING

 reserves the right to make changes without further notice to any products herein to 

improve reliability, function or design. 

FULLING

 does not assume any liability arising out of the 

application or use of any product or circuit described herein; neither does it convey any license 
under its patent rights of others.   
 

FULLING

’s general policy does not recommend the use of its products in life support or aircraft 

applications wherein a failure or malfunction of the product may directly threaten life or injury. 
According to 

FULLING

’s terms and conditions of sales, the user of 

FULLING

’s products in life 

support or aircraft applications assumes all risks of such use and indemnifies 

FULLING

 against all 

damages. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for MD2278









Reviews: