ASE 65
3
16
5
ASE 65
3
24
6
ASE 65
3
32
7
ASE 65
4
16
5
ASE 65
4
24
6
ASE 65
4
32
7
ASE 85
4
32
8
ASE 65
5
16
6
ASE 65
5
24
8
ASE 65
5
32
8
ASE 85
5
32
8
ASE 85
5
41
9
ASE 125
5
49
10
ASE 65
5
7
/
₈”
16
7
ASE 85
5
7
/
₈”
24
8
ASE 85
5
7
/
₈”
32
10
ASE 125
5
7
/
₈”
32
10
ASE 125
5
7
/
₈”
41
8**
ASE 125
5
7
/
₈”
49
8**
(h)
(h)
2
4
3
5
6
8
9
7
10
1
Ø 150 mm
Ø 125 mm
Ø 100 mm
Ø 75 mm
5
Fig. 4
Fig. 5
Fig. 3
3 Preparation for use
3.1 Transport and storage
Protect the hose reel from rain, snow aggressive
atmospheres and any other damaging circuimstances.
3.2
Installation and assembly
3.2.1 Assembly
Assembly may only be carried out under consideration of
these assembly instructions and applicable regulations.
1. Remove all the packaging from the product and leave it
assembled on the pallet.
Item 2-6 does not apply if the reel has been
ordered complete with hose.
When assembling the hose, ensure that the reel
is blocked correctly. Risk of personal injury.
2. Place the front stop beam (1, Fig. 4) at the correct
height for the selected hose size.
3. Secure the pallet and pre-load the hose reel according
to the table. Turn the drum in the direction indicated by
the arrow (2).
4. Any reduc
ti
on (3) is drawn through the hose connec
ti
on
(4). Install the hose (5) on the hose connection (4) using
hose clamps (6).
Dim.
Hose length
Bias
Product
(in)
(ft)
(turns)*
*
The calculations only apply when using Movex original AG hose,
Movex 6.2 lb nozzle and an installation height of 20 ft.
** Extra spring assembly included.
Maximum mounting height (h, Fig. 5)
- 10 feet at hose length 16 feet
- 18 feet at hose length 24 feet
- 26 feet at hose length 32 feet
5.
Secure the hose by first placing the rubber cloth (7)
around the hose. Then pull the hose clip (8) through the
holes (9) and around the rubber sheet to lock securely.
The hose stop should, when in the retracted
position, rest against the drum and fit between
the end cap and the adjacent hose. Risk of wear.
6. Install the hose stop (10) in the desired position.
Release the latch and wind the hose until it stops
against the hose stop.Check that the hose stop is
working and assembled correctly.
7. Remove the roller from the pallet and install it onto
the
ceiling or wall using correctly dimensioned
fastening elements.
8. Check the roller and the ventilation ducts properly, so
that foreign objects are not present. Remove any such
objects immediately.
9. Seal and install the ventilation ducts directly to the
duct connection on the roller, or use a hose ASL 160
between the duct and roller (see
Accessories
).
10. Check that the gaskets and connections on the roller
and ventilation duct are tight
.
11. Install the nozzle.
12.
The hose winding reel is ready for use.
5 7/8”
5”
4”
3”
Summary of Contents for Movex ASE Series
Page 1: ...MANUAL A17W23_MASE_MUS_EN...
