8
EN
6)
Press the
number buttons
,
PLAY
/
K
, or
STOP
/
L
to select
your desired position number, then press
F.FWD
/
B
.
•You can select position number 01-99.
•If [ON] appears on the right side of “SKIP”, press
PLAY
/
K
or
STOP
/
L
to point to “SKIP”. Then, press
F.FWD
/
B
to select [OFF].
•If you want to remove scrambled signals, press
PLAY
/
K
or
STOP
/
L
repeatedly to point to
“DECODER”. Then, press
F.FWD
/
B
to select [ON].
7)
Press
PLAY
/
K
or
STOP
/
L
to select “CHANNEL”, then
press
F.FWD
/
B
.
Press
PLAY
/
K
or
STOP
/
L
. The VCR tuner will begin to
search up or down automatically. When a channel is
found, the VCR will stop searching and the picture will
appear on the TV Screen.
•You can select desired channel number by using
the
number buttons
. You must refer to the following
Channel Plan table and press three digits to select the
channel number.
(To select channel 24, press “
0
” button first and then
press “
2
” and “
4
”.)
•If this is the channel you want, press
F.FWD
/
B
.
This VCR can receive Hyper and Oscar frequency bands.
8)
Press
MENU
to exit.
Note:
To confirm that a channel has been added, press
CHANNEL
(
K
/
L
).
To Skip a Preset Channel
The channels you can no longer receive or seldom watch can
be set to be skipped when you access channels by pressing
CHANNEL
(
K
/
L
).
• Use the remote control for this procedure.
1)
Press
MENU
.
2)
Press
PLAY
/
K
or
STOP
/
L
to select “INITIAL”, then press
F.FWD
/
B
.
3)
Press
PLAY
/
K
or
STOP
/
L
to select “CH TUNING”, then
press
F.FWD
/
B
.
4)
Press
PLAY
/
K
or
STOP
/
L
to select “MANUAL”, then
press
F.FWD
/
B
.
5)
Press
PLAY
/
K
or
STOP
/
L
to select “POSITION”, then
press
F.FWD
/
B
.
6)
Press the
number buttons
,
PLAY
/
K
, or
STOP
/
L
to select
relevant position number, then press
F.FWD
/
B
.
7)
Press
PLAY
/
K
or
STOP
/
L
to select “SKIP”, then press
F.FWD
/
B
to select [ON].
•To memorize the channel again, press
F.FWD
/
B
. “ON”
will change to “OFF”.
Note for 29A-654 and 29A-754 only
•The VCR refers to the PDC channel which was
memorized into position 01 when you set the Auto
Clock.
The position 01 must therefore be set “SKIP” to [OFF].
8)
Press
MENU
to exit.
Note:
To confirm that a channel has been deleted, press
CHANNEL
(
K
/
L
).
Channel Reprogramming
You can replace two channels.
• Use the remote control for this procedure.
1)
Press
MENU
.
2)
Press
PLAY
/
K
or
STOP
/
L
to select “INITIAL”, then press
F.FWD
/
B
.
3)
Press
PLAY
/
K
or
STOP
/
L
to select “CH TUNING”, then
press
F.FWD
/
B
.
4)
Press
PLAY
/
K
or
STOP
/
L
repeatedly to select “MOVE”,
then press
F.FWD
/
B
.
5)
Press
PLAY
/
K
or
STOP
/
L
repeatedly to select the position
number you want to change the channel, then press
F.FWD
/
B
.
•You cannot select a position number where “- - -”
appears next to the number. This is because SKIP is set
to [ON] for this position number.
•When a weak signal is received in Channel
Reprogramming mode, you can change the background
to solid blue by pressing
TAPE COUNTER RESET
.
If you press the button again, the background will return
to the static screen.
6)
Press
PLAY
/
K
or
STOP
/
L
repeatedly until the channel
move to another position number, then press
F.FWD
/
B
.
Channel Plan
CH Indication
TV Channel
02 – 12
E2 – E12
13 – 20
A – H (only ITALY)
21 – 69
E21 – E69
74 – 78
X, Y, Z, Z+1, Z+2
80 – 99,100
S1 – S20,GAP
121 – 141
S21 – S41
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
CH TUNING
AUTO
MANUAL
MOVE
MANUAL
POSITION
CHANNEL
DECODER
SKIP
P08
008
[OFF]
[OFF]
MENU
TIMER
SET UP
INITIAL
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
MANUAL
POSITION
CHANNEL
DECODER
SKIP
P08
008
[OFF]
[ON]
CH TUNING
AUTO
MANUAL
MOVE
MENU
TIMER
SET UP
INITIAL
29A-650(EN).fm Page 8 Wednesday, October 27, 2004 10:40 AM
All manuals and user guides at all-guides.com
