12
Re-syncing Multiple Sequencers
There can be unique situations where multiple sequencers fall out of
sync. For example, loss of sync can occur when a branch circuit experi-
ences an overload or high voltage and triggers an EVS shutdown of one
or more units. If you are using a rack mounted Contractor unit equipped
with SmartSequencing, you can re-establish sync by pressing and holding
the Start Sequence pushbutton on the Primary Unit for several seconds.
Sync can also be re-established by rotating the key on the primary unit
from the REMOTE to the OFF position and then back to REMOTE. When
pressing and holding the pushbutton on dedicated SmartSequencing
units, the Primary Unit commands the Secondary Units to “Go Home”
and all units will sequence down in reverse order. Once the chain of
sequencers has cycled off, the sequencers can be sequenced on again
by pressing the START SEQUENCE button or turning the key switch to the
ON position.
Legacy connected sequencers can also be re-synced if the sequencers
are operating Momentary Mode. The units will resync can be accom-
plished by pressing and holding the Start Sequence pushbutton. Unlike
the SmartSequencing chains, units will cycle down, yet may not cycle
down in hierarchical order. It is advised that all sound sources be muted
before a re-sync action is initiated. Once the re-sync is initiated, unit will
cycle down and return to an off state. A sequence can now be “ramped
up” in order.
SPECIFICATIONS
Maximum AC Current Rating:
• CN-15MP - 15 Amps, 120 VAC (Thermal circuit breaker)
• CN-20MP - 20 Amps, 120 VAC (No circuit breaker))
AC Cord:
• 3/14 AWG, 10 feet, black, fixed, NEMA 5-15P plug
AC Receptacles:
• AC Outlets: 2 Switched NEMA 5-15R (1 duplex)
Surge/Under-Overvoltage Protection:
• AC Undervoltage Protection: EVS, 77VAC+/-3VAC
• AC Overvoltage Protection: EVS, /-5VAC
• AC EVS Protection Activate/Deactivate Modes: ON or OFF DIP 9 (configurable)
Operating Temperature Range:
• 5C (40F) to 40C (105F) degrees
Humidity Range:
• <90% rH (Relative Humidity)
User Interface:
• Thermal Circuit Breaker: Bottom panel, pushbutton (CN-15MP only)
• Front panel diagnostic indicators: Primary link, Secondary link, Power, Extreme Voltage
• Side Panel DIP Switches: Hidden by security cover, 1 Minute Delay,
2 Minute Delay, 4 Minute Delay, Force Off NO/NC, 12V Mode ON/OFF, GND Mode On,
Momentary/Maintained, Primary/Secondary, EVS ON/OFF
• Potentiometer: Side panel, time calibration hidden by security cover, fine tune delay
adjust
Control/Status/Triggering (Front Panel):
• Remote Terminal: +5-30VDC IN, 12VDC (12mA) OUT
• SmartSequencing: Phoenix type 4-Pin Connector, with Screw Terminals, Primary &
Secondary Links (Current Loop - 1000’ maximum)
• Remote Terminal: Phoenix type 5-Pin Connector with Screw Terminals;
+12V, STAT, REM, GND, DLY OUT (Class 2 Wiring)
• Force Off: Phoenix type 2-Pin Connector with Screw Terminals, (Class 2 Wiring)
Power Consumption (No Load): 10 Watts
Safety Agency: NRTL-C CSA/NRTL Compliant:
Specifications subject to change due to product upgrades and improvements.
Full Warranty and Policy information available at
www.furmancontractor.com
15 YEAR LIMITED PRODUCT WARRANTY*
Furman warrants to the original purchaser of this product for a
period of fifteen (15) years from the date of purchase, that the
unit shall be free of defects in design, material or workman-
ship, and Furman will repair or replace any defective unit.
CAUTION! WARRANTY LIMITATION FOR INTERNET PURCHASERS
Furman products purchased through the Internet do not carry a valid
Product Warranty unless purchased from an Authorized Furman
Internet Dealer and the original factory serial numbers are intact
(they must not have been removed, defaced or replaced in any way).
Purchasing from an Authorized Furman Internet Dealer insures that
the product was intended for consumer use, has passed all quality
inspections and is safe. Buying through auction sites or unauthorized
dealers may result in the purchase of salvaged, failed and/or products
not intended for use in the US. In addition, Authorized Furman Internet
dealers have demonstrated sufficient expertise to insure warranty
compliant installations.
For a list of Authorized Furman Internet Dealers
go to www.furmansound.com
