background image

 

 

 

WARNING: 

 Indicates a potentially dangerous 

condition.  Use extreme caution when 

performing this task.

CAUTION:

  Indicates a critical procedure for 

safe and proper operation of the controller.

NOTE:

  Indicates a procedure or function that 

is important for the safe and proper operation of 

the controller.

   

General Safety Information

•  Read all of the instructions and cautions in the manual 

before beginning installation.

•  There are no user serviceable parts inside the Furrion

Rear camera system Do not disassemble or attempt to 

repair any part of the camera system.

•  Disconnect all sources of power to the camera before 

installing.  

•  There are no fuses or disconnects on the Furrion reversing

camera unit.  Install external fuses/breakers as required.

•  Do not allow water to enter the LCD Display.

• 

Excessive heat can be caused from a loose connection.

Safety Instructions

Please Read these instructions carefully before installation and operating your

Furrion reversing camera unit.

The following symbols are used throughout this manual to indicate potentially 

dangerous situations or mark important safety instructions.

Connect 12V power cable to the camera unit using waterproof 

connectors.

2

Summary of Contents for FRCBRKT-BL


















Reviews: