U
lstein Power & Control AS
This document and its content is the property of ULSTEIN. Non-
public information contained herein shall be treated as
Confidential Information. No use, copying, citation or publication
of this document or its content is permitted without prior written
consent from ULSTEIN. Any conflicts arising from unauthorized
use shall be governed by the laws of Norway.
File Name:
BRI-D32004-01II (D)
System Installation
Manual.doc
Page:
Page 35 of
56
4.1.2.
Installation instructions
Motion sensor (805):
Mount the Motion sensor/sensors.
Use the standard mounting bracket when mounting the motion sensor.
In addition, a few important rules must be observed while selecting a mounting location:
A.
Microwave radiation passes through glass and non-metallic walls. Be sure to adjust the
MW range so that it does not exceed the room limits, or else motion in the next room or
moving traffic along the outer side of the wall will cause the MW detector to trip.
B.
Large reflecting objects (especially metals) in the coverage area can distort the
microwave detector's coverage pattern.
C.
If two motion sensors are installed in the same room or on opposite sides of a shared wall,
they should not face each other and must be mounted at least 2 meters apart.
D.
The motion sensor cover area shall only be available in positions on the bridge giving
proper look out. Find more information about settings in chapter 11.
4.1.3.
Installation considerations:
A.1 General
Follow requirements in IMO resolution MSC.128 (75) concerning the installation of the
BNWAS.
A.2 Location of reset function
(128/A4.1.3.1) It shall not be possible to initiate the reset function or cancel any audible alarm
from any device, equipment or system not physically located in areas of the bridge providing
proper look out (this includes coverage area from motion sensors).
A.3 Reset facilities
(128/A5.1.4) Means of activating the reset function shall only be available in positions on the
bridge giving proper look out and preferably adjacent to visual indications. Means of activating
the reset function shall be easily accessible from the conning position, the workstation for
navigating and manoeuvring, the workstation for monitoring and the bridge wings.
A.4 Visual indications
(128/A5.2.2 part) Flashing indications shall be visible from all operational positions on the
bridge where the OOW may reasonably be expected to be stationed.
A.5 First stage bridge audible alarm (alarm 2)
(128/A5.2.3 part) This alarm shall be audible from all operational positions on the bridge where
the OOW may reasonably be expected to be stationed.
NOTE: Bridge includes wheelhouse and bridge wings.
Summary of Contents for FA-150
