background image

6

Transmitter: T4YF-2.4G

T4YF-2.4GHz Transmitter of FHSS system

Transmitting on 2.4GHz band
Operating system: 2-stick, 4-channel system
Power supply: 6V (4 AA size batteries)
Current drain: 90mA

Receiver: R2004GF

4 channel receiver of FHSS system

Receiving on 2.4GHz band
Power requirement: 4.8V or 6V (shared with servo)

*1

Current drain: 30mA (at no signal)
Size: 1.54x1.02x0.39” (39x26x10mm)
Weight: 0.49oz. (14g)

CONTENTS AND SPECIFICATIONS

*Specifications and ratings are subject to change without notice.

GLOSSARY 

It will be helpful to understand the following terms before reading the rest of the manual.  

Reversing (servo reversing) 

- A function that allows the user to determine the direction of response of each servo. If, after 

hooking up the servos, a control on the model responds in the wrong direction, the user may change the servo's direction so 
the control responds correctly. 

Throw 

- When speaking of a control surface (such as an elevator or aileron), the throw is the 

distance the surface moves. Control surface throw is usually measured at the trailing edge of 
the surface and is expressed in inches or millimeters. The model in the diagram has 1/2" [13mm] 
of up elevator throw. Throw can also refer to the distance a servo arm (or wheel) travels.

Mixing 

- Two (or more) servos can be made to operate together either by mechanically joining 

the wires (with a Y-connector) or by electronically “joining” them through programming functions 
in the transmitter. When servos are electronically joined via programming, they are said to be 
“mixed.” 

*1

WARNING

l 

NEVER

 use dry batteries for the power supply of the 

R2004GF as they may cause difficulties.

NOTE

: Futaba FHSS system, T4YF-2.4G transmitter and 

R2004GF receiver, does not work with current Futaba 
FASST system. Please use T4YF-2.4G and R2004GF in 
pairs. Futaba FASST system and FHSS system are not 
compatible each other.

Summary of Contents for 4YF-2.4GHZ
















Reviews: