103
< Linkage menu >
*It cannot be used in FASST mode and S-FHSS mode.
*Only receiver voltage and EXT voltage can be used in
FASSTest12CH mode.
*The FASSTest18CH /T-FHSS mode can use all the telemetry
functions.
Telemetry: Voltage [Battery]
Displaying data from the receiver battery voltage
In this screen, the battery voltage of a receiver is
displayed.
If it becomes higher or lower than the settin, an
alarm and/or vibration will alert you.
Battery voltage
Sets the voltage on
w h i c h t h e a l a r m
operates.
↓ The "down" arrow
will indicate that an
alarm will sound when
the voltage drops to
below the setting.
Alarm is chosen from
Buzzer, Voice, and
Inhibit.
Allows Speech to be
turned ON or OFF.
ŏ
Tap the [Voltage] button in the Telemetry screen
to call the setup screen shown below.
Max. and min. values
s i n c e t h e p o w e r
was turned ON will
display.
In this screen, the battery voltage is displayed.
In order to use this function, it is necessary to
connect External voltage connector of R7008SB
⇔
SBS-01V
⇔
Battery
SBS-01V measures two batteries. The power
battery connected to two lines is displayed on EXT-
VOLT. The battery for receivers connected to 3P
lines is displayed here.
*SBS-01V must be installed in the aircraft.
<
Two examples of wiring are shown
>
*Refer to the manual of SBS-01V for the details of
wiring.
WR6%86
SRUW
WR6%86
SRUW
56%
56%
Drive battery 1
(EXT Battery)
Receiver battery
Receiver battery
Drive battery 2
(EXT Battery)
Drive battery 1
(EXT Battery)
Drive battery 2
(EXT Battery)
6ZLWFK
Power supplies
for servos
$QRWKHUSRZHU
VXSSO\+XE
S.BUS2
servos
Two drive batteries are measured (R7008SB use)
Two drive batteries and power supplies for servos are measured (R7008SB use)
●Battery voltage measurement for receivers [R7008SB use]
●The drive battery 1 is measured in an EXT port [R7008SB use]
●The drive battery 2 is measured in an EXT line [SBS-01V use]
●Battery voltage measurement for receivers [R7008SB use]
●The drive battery 1 is measured in an EXT port [R7008SB use]
●The drive battery 2 is measured in an EXT line [SBS-01V use]
●The voltage for servos is measured in a power supply line [SBS-01V use]
Normal Line
Normal Line
EXT Line
EXT Line
*SBS-01V measures two voltage. One corresponds to high voltages, such as a drive battery,
with an EXT line. Another is a normal line and is measurement of the battery for receivers of a
line connected to 3P connector, or the battery for servos.
Alarm set
1. Tap Alarm and choose from Bu
]]
er,
Voice, and Inhibit.
2. Choose "Inhibit" for Vibrator if no
t
using
the vibrator alarm. If using vibrator,
choose one of the three types.
3. Tap to the Limit [4.0V] item .
4. Adjust the rate using the "
ʈʈ
" "
ʈ
" "
ʆ
"
"
ʆʆ
" buttons.
Initial
value:
4.0V
Adjustment range: 0.0V~100.0V
*When the screen is tapped for one second, the rate is
reset to the initial value.
5. To terminate the input and return to the
original state, push the H/E button.
Vibrator choices are
type1-3, and Inhibit.
ŏ
Return to
Linkage menu