background image

GY520 Link

CIU-2 and GY520 connection

Connect GY520, CIU-2 USB adapter and power supply as shown below.

Installing the CIU-2 device driver

A  CIU-2  USB  adapter  is  necessary  to  execute  this  software.  Before  using  this 
software, please install the CIU-2 device driver. If the CIU-2 USB device driver has 
already been installed, advance to the next step.

The CIU-2 device driver is available at the download corner of our home page.

Connection method

1.

 Connect the CIU-2 to the USB port of the PC.

2.

 Using the connection cord connect the 3 pin connector of the CIU-2 to the rudder 

input connector of the GY520.

3.

 Connect the receiver battery or a 5V power source to the sensitivity input connector 

of the GY520.

GY520

CIU-2 USB adapter

Connect to the USB port 

on your PC.

* If  the  GY520  is  already  mounted  and  wired  to  the  helicopter,  disconnect  the 

receiver side of the connection cord connected to the rudder input connector and 
connect it to the CIU-2 connector. Leave the sensitivity input connector connected 
to the receiver. And then turn the GY520 power on.

Receiver battery or 5V power source

Rudder

input

Sensitivity

input

(CIU-2)

(Battery)

Summary of Contents for GY520












Reviews: