background image

 

U

GENERAL INFORMATION 

 
Thank you for buying the Futtura LT600 laser! Although the 
LT600 is simple to use, we recommend that you read this 
manual before operating the laser. 
 

Description: 

 
The LT600 is a visible universal laser that can be used for 
leveling, vertical alignment, squaring, and single and dual 
slope grade control.  

 

It has a digital grade display and is ideal for machine control 
and other dual grade applications. It’s totally waterproof and 
has a beam designed for pipe laying. It also has scanning 
and constant squaring for interior jobs. 

 

Other advanced features include: totally automatic self-
leveling in both horizontal and vertical modes; electronic 
calibration by the user; and a detachable keypad that can be 
used as a remote control. 
 

Specifications: 

 
Recommended use  

 

1,000 ft. (300 m) diameter 

 

Accuracy  

< 2.4mm @ 30m  

 

Leveling range 

±

 10% in X and Y axes 

 

Grade range    

 

-10% to +10% in X,Y & Z  

 

Rotation speeds 

60, 150, 300, 450, 600, 720 
rpm 

 

Scanning lengths 

Choice of 3 

 

Laser battery  

NiMh rechargeable  

 

Charging time 

15 hours 

 
 

Battery 

life 

  40 

hours 

 

Remote control batteries 

2 AAA alkaline 

 

Dimensions 

 

 

5” x 4 ½” x 8 1/2” 
12.5 x 11.5 x 21.9 cm 

 

Weight   

 

 

7 ¾ lbs. (3.5 kg) 

 

Environmental   

 

Laser is waterproof: IP64 
Remote control is weather-
resistant 

 

Laser Diode    

 

Visible 635 nm, 2mW 

    FDA/CDRH: 

Class 

IIIa 

 

    IEC 

Class 

II 

Summary of Contents for LT600




















Reviews: