background image

10 

FuturaSun srl – The specifications in this manual are subject to revisions without further notice  

RECYCLABLE:

  most  of  the 

photovoltaic 

modules 

are 

recyclable.  They  should  not  be 
thrown into landfill without a proper 
method  for  recycling.  Aftert  the 

approval  of  EU  Directive  2012/19/Ue  the 
photovoltaic  modules  are  classified  as  electronic 
waste.

 

 

 
FRAGILE:

 the photovoltaic modules 

are manufactured using a glass front 
which makes up approximately 70% 
of  the  total  materials  used  to 
construct  them.  Although  the 

modules are stiffened by an aluminium frame, any 
direct impact to the glass or on the corners of the 
modules  should  be  avoided.  Avoid  flexing  the 
laminates  or  applying  non  distributed  loads  and 

stresses.  Avoid  scratching  the  surface  of  the

 

exterior  glass  or  backsheet.  Do  not  apply  any 
forces to the backsheets. 

 
 
 

HANDLE  WITH  CARE:

  during  the 

operation of shipping and storage of 
the  modules  use  maximum  care  to 
ensure  the  full  integrity  of  the 
modules.

 

 

9c) How to Handle the Pallet 
 

During the handling of the pallet make sure to pay 
the  utmost  attention.  The  packaging  must  be 
raised/moved  exclusively  with  fork-lift  trucks  or 
hand  pallet  trucks  fitted  with  forks  of  length 
appropriate to its size and weight.  

 

Pay  attention  during  the  stages  of  handling  and 
unpacking. Verify that the package is positioned on 
a  surface  that  is  either  flat  or  not  excessively 
deformed to a point that would impart an inclination 
to the pallets which could damage the PV modules.  
 
FUTURASUN 

DOES 

NOT 

ASSUME 

RESPONSIBILITY  IN  THE EVENT OF  DAMAGE 
TO 

THE 

MODULES 

ARISING 

FROM 

MANAGEMENT  OF  THE  PACKAGING  THAT  IS 
IMPROPER OR DIFFERENT FROM WHAT WAS 
STATED IN THIS DOCUMENT. 

9d) Unpackaging  

 
Observe  the  following  procedures  for  the 
unpacking of modules: 

  Place  the  packaging  on  a  stable  and  flat 

surface  

  Using  a  cutter,  cut  the  plastic  wrap 

surrounding  the  package  or  to  open  the 
paper box  

  Remove the plastic wrap  

  Remove the upper cover  

  Recover the flash list (for record keeping) 

  Using a cutter, cut the straps  

  Remove  the  PV  modules  and  their 

protective corners without damaging 

 
Note: avoid storing partial packaging! 
Once  you  have  removed  the  strapping  the 
packaging must no longer be moved!! 

 

Summary of Contents for FU M Series












Reviews: