background image

 

Extra Set of Plastic Picture Covers 

You will find an extra set of clear plastic picture covers this is to be used if you 
want to use only the photo memories only. 
1. Remove numbered plastic cover from each key 0-9 and put them aside. 
2. You will need a pictures approximately 1” x 1¼” inch. 
3. Place picture into key. 
4. Replace with new all clear plastic covers. 

CONSUMER INFORMATION 

This equipment complies with Part 68 of the FCC rules and the requirements 
adopted by the ACTA On the bottom of this equipment is a label that contains, 
among other information, a product identifier of US: 4VKTE09BFC-1007.  
If requested, this number must be provided to the telephone company. 

The applicable jacks (i.e. RJ11C) for this equipment are provided in the packaging 
with each piece of approved equipment. The jacks are certified by Universal 
Service Order Codes (USOC). 

A plug and jack used to connect this equipment to the premises wiring and  
telephone network must comply with the applicable FCC Part 68 rules and  
requirements adopted by the ACTA. A compliant telephone cord and modular plug 
are provided with this product. They are designed to be connected to a compatible 
modular jack that is also compliant. See installation instructions for details. 

The REN is used to determine the number of devices that may be connected to a 
telephone line. Excessive RENs on a telephone line may result in the devices not 
ringing in response to an incoming call. In most but not all areas, the sum of RENs 
should not exceed five (5.0). To be certain of the number of devices that may be 
connected to a line, as determined by the total RENs, contact the local telephone 
company. [For products approved after July 23, 2001, the REN for this product is 
part of the product identifier that has the format US:AAAEQ##TXXXX.

 

The digits  

represented by ## are the REN without a decimal point (

e.g.,

 03 is a REN of 0.3). 

For earlier products, the REN is separately shown on the label.] 

If this equipment FC-1007 causes harm to the telephone network, the telephone 
company will notify you in advance that temporary discontinuance of service may 
be required. But if advance notice isn’t practical, the telephone company will notify 
the customer as soon as possible. Also, you will be advised of your right to file a 
complaint with the FCC if you believe it is necessary. 
The telephone company may make changes in its facilities, equipment, operations 
or procedures that could affect the operation of the equipment. If this happens the 
telephone company will provide advance notice in order for you to make 
necessary modifications to maintain uninterrupted service. 

If you experience trouble with this equipment, disconnect it from the network until 
the problem has been corrected or until you are sure that the equipment is not  
malfunctioning. 

Please follow instructions for repairing if any (e.g. battery replacement section); 
otherwise do not alter or repair any parts of device except specified. 

Summary of Contents for FC-1007












Reviews: