background image

14

6. Warm Suggestion

1. Please do not use smart key and original remote key mixed.

2. Please do not put smart key inside vehicle for long time if you are not driving.

3. Please press

to unlock the door if passive unlock action fails.

4. Please do not put smart key and smart phone together.

5. This product must be installed by professional vehicle electrical technician.

6. The battery model must be 3V CR2032, please buy from your dealer.

7. Safety Caution

The driver must follow the following instructions to avoid dangers and injuries.

1) To avoid pinching injury or other accident, do not put hand, head or other things

on the window when leaving the vehicle.

2) To protect children from pinching injury or other accident by triggering the

window closer, do not leave them alone inside the vehicle.

Change the battery in time when receiving low power warning. If smart key is put

inside the vehicle or keep battery for long time without changing, the vehicle could

be locked possibly.

8. FAQ

8.1. Smart key (PKE) failure (Attached picture 8.1)

1) Long press button on smart key, LED not working. Battery runs out or damaged;

2) Lock/unlock repeat within 1M. Check 3D antenna wire damaged or not;

3) Key A not working, Key B working, UHF sender of A might be damaged.

8.2. General start failure

1) Check lamp, steering lamp, interior lamp turned off or not? Maybe battery out;

2) If the battery is normal, check if the fuel circuit is cut off or not? Recover it and

check if the vehicle can start or not;

3) Check if the IMMO is released or not; Check if the DIP settings is correct or not;

4) The Start button can be switched at “ACC”, “ON”. Step on the brake, the green

led on button lights, but there is no start output (by listening, normal starting can

trigger the relay voice from push start main unit); Check the communication cables

between Start Controller and PKE unit, are they connected in bad contact?

8.3. Start failure after short time parking

1) On site check lamp, steering lamp, interior lamp are turned off or not? Maybe

battery is dead;

2) Test the static current after locking, normally less than 80mA or not;

3) If the static current is a bit higher, for example 100mA, but lock the vehicle by

original key only causing 40mA, please change the connection point of lock signal

wire (necessarily connect with primary lock).

Summary of Contents for PKE-100 (V3)

















Reviews: