background image

 

Make sure that the available voltage is not higher than stated at the end of this manual. 

Make sure the power cord is never crimped or damaged by sharp edges. If this would be the 
case, replacement of the cable must be done by an authorized dealer. 

Always disconnect from the mains, when the device is not in use or before cleaning it. Only 
handle the power cord by the plug. Never pull out the plug by tugging the power cord. 

During initial start-up some smoke or smell may arise. This is a normal process and does not 
necessarily mean that the device is defective, it should decrease gradually. 

Please don't project the beam onto combustible substances. 

Fixtures cannot be installed on combustible substances, keep more than 50cm distance with 
wall for smooth air flow, so there should be no shelter for fans and ventilation for heat 
radiation. 

If  the  external  flexible  cable  or  cord  of  this luminaire is damaged, it shall be exclusively 
replaced by the manufacturer or his service agent or a similar qualified person in order to 
avoid a hazard. 

3.

 

Operation Instructions  

-The moving head is for beam effect for onsite decoration purpose. 

-Don’t turn on the fixture if it’s been through severe temperature difference like after 
transportation because it might damage the light due to the environment changes. So make 
sure to operate the fixture until it is in normal temperature. 

-This light should be keep away from strong shaking during any transportation or movement. 

-Don’t pull up the light by only the head, or it might cause damages to the mechanical parts. 

-Don’t expose the fixture in overheat, moisture  or  environment  with  too  much  dust  when 
installing it.  And don’t lay any power cables on the floor. Or it might cause electronic shock to 
the people.  

-Make sure the installation place is in good safety condition before installing the fixture. 

-Make sure to put the safety chain and check whether the screws are screwed properly when 
installing the fixture. 

-Make sure the lens are in good condition. It’s recommended to replace the units if there are 
any damages or severe scratch. 

Summary of Contents for Beam 300










Reviews: