background image

 

 

5

make fir, it maybe the trigger has out of work. Please replace the parts according to 
the above method to obviate trouble. 

 

Exchange Xenon Lamp 

 

Step1: Take off the lamp head cover. Take off the 10 pieces six screws with 
hexangular screwdriver on the lamp head cover. 
 
Step2: Take off the epoxy board. Take off the 10 pieces hexangular screw with 
hexangular screwdriver on the epoxy board. Do not put much pressure when pulling, 
otherwise will snap the power line of fan. 
 
Step3: Take off nut M13 on the Xenon lamp head (anode) and then take off anode 
line, follows take off nut M13 on the end of xenon lamp (cathode) and then take off 
cathode line. During take off then xenon lamp, must hold the lamp in hand 
immobility. Do not let the lamp fall down or make any ram otherwise the lamp will 
break up and influence the cleaning inside the lamp box. 
 
Step4: Set the xenon lamp or the light head, epoxy board and light head cover 
according to the contradictorily step. 
 
Step5: Set the case of light head at original situation. 
 
 

Announcement 

 

When we delivery the goods out of factory, it is function is goods and package is 
well. All users must obey all noted attentions and operate rules. We won’t sere free of 
charge repair if the destroy be caused by your own wrong operation. All problems 
which be caused by not operate accord the user manual also not the duty of 
distributor. 
 

 
 
 
 
 
 

Summary of Contents for STAR SEARCH 4000









Reviews: