gm-elektronik.swiss | adm@gm-elektronik.swiss
Datasheet 1811.001
MICROPHONE CONSOLE VA-FMCT-500
Page 6 | 12
general pre-selection.
2. Press the PTT key and hold it down. The red ALARM LED will light up and the green indicator will show that it is possible
to speak via the microphone. If no particular zones have been selected in advance, the message will be broadcast in all
the zones. If you wish to address the message only to some specifi c zones or groups of zones, see point 2.4 (sending
out messages to selected broadcasting zones,
page 7)
. To end the hands-free emergency message, release the PTT key
and press the EMERGENCY button.
N.B.: Remember that the PTT key has priority over any pre-recorded message already being sent out.
NOTE: An emergency condition can be stopped only by a station with a higher priority or by local commands by the VA-500.
26
UK
TSC6000-EN
3.2 Sending out emergency messages hands-free
To send out an emergency message hands-free to the broadcasting zones, it is necessary rst of all
the place the station in the emergency mode:
1.
Lift the lid protecting the
EMERGENCY
key (
4
) and press the key. It will light up steadily to indicate
that the emergency mode has been activated. The background of the display will change colour
and all the zone keys will turn green to indicate general pre-selection.
2.
Press the
PTT
key and hold it down. The red
ALARM
LED will light up and the green indicator will
show that it is possible to speak via the microphone. If no particular zones have been selected
in advance, the message will be broadcast in all the zones. If you wish to address the message
only to some speci c zones or groups of zones, see point 3.4,
Sending out messages to selected
broadcasting zones
(page 28).
N.B.: Remember that the PTT key has priority over any pre-recorded messages already being
sent out.
To end the hands-free emergency message, release the
PTT
key and press the
EMERGENCY
button
again, remembering to close the lid.
NOTE: An emergency condition can be stopped only by a station with a higher priority or by
local commands by the system (VAIE 6500 or VAC 2006).
The status of the EMERGENCY key indicates the condition of the system:
• OFF:
Emergency de-activated
• Flashin:
Emergency under way, activated by another station or by local commandsby the system
• Steady ON: Manual emergency activated from the station itself
All the keys are active so as to enable the operator to manage the emergency.
2.3. Sending out pre-recorded evacuation / alert messages
To send out pre-recorded evacuation or alert messages (stored in the memory of the control unit connected to the
VA-FMCT-500), after activating the emergency mode (see point 2.2) press ALERT or EVAC to send out an alert or evacuation
message respectively in the broadcasting zones.
27
UK
TSC6000-EN
The status of the
EMERGENCY
key indicates the condition of the system:
•
OFF
= emergency de-activated.
•
Flashing
= emergency under way, activated by another station or by local commands
by the system.
• Steady
ON
= manual emergency activated from the station itself.
All the keys are active so as to enable the operator to manage the emergency.
3.3 Sending out pre-recorded evacuation/alert messages
To send out pre-recorded evacuation or alert messages (stored in the memory of the control unit
connected to the
TSC6000-EN
), after activating the emergency mode (see point 3.2) press
ALERT
or
EVAC
to send out an alert or evacuation message respectively in the broadcasting zones.
The indicators (
I
) will turn red: if the evacuation message (
EVAC
) was selected they will remain steady
ON. If the alert message (
ALERT
) was selected they will be ashing.
Again in this case, if no particular zone was selected beforehand, the selected message will be sent
out by default to all the zones. If you wish to send the message out only in some zones or groups of
zones, consult point 3.4,
Sending out messages to selected broadcasting zones
(page 28).
To stop pre-recorded messages, hold the
RESET/ACK
button down until the messages are deactivated
(about 2 seconds).
By pressing the
EMERGENCY
button again, the messages will be deactivated and the station will
exit the emergency mode. Remember to close the lid again.
The indicators (I) will turn red: if the evacuation message (EVAC) was selected they will remain steady ON. If the alert message
(ALERT) was selected they will be flashing.
