background image

3

LI0055 – Revision 25 June 2012

Contents

Introduction .................................................................................. 4

The Package.............................................................................................. 4
Assembling the 67AX System ..................................................................... 4

Calibration and Verification ............................................................. 6

Calibrating the microphone .......................................................................... 6
Verifying the microphone ............................................................................ 6

Technical Specifications .................................................................. 7

Dimensions and Data for 67AX ................................................................... 7

Ordering Information ...................................................................... 8

Accessories ............................................................................................... 8
Calibration ................................................................................................. 8
Warranty ................................................................................................... 8
Service and Repairs .................................................................................... 9

Summary of Contents for 67AX










Reviews: