G-Tec Basic TTCF-6 How To Operate Download

Page: 9 / 11

Optional/Replacement Equipment

Products available from G-Tec Inc

1-800-725-6400

•

Flowmeter Kit

•

Purge Valve Kit

•

Attachable Tool Tray

•

Domestic Adapter Fittings Kit

•

Super Duty Adapters (set of 8)

•

Honda Adapters (set of 7)

•

Push-On Adapters (set of 8)

•

Banjo Adapters (set of 4)

•

Complete Electrical Box Harness w/Float

•

Remote Spin-On Filter Bracket

•

Magnetic Spin-On Non By-Pass Filters

•

Heater Kit

•

Baldor/Viking Pump & Motor

•

Complete Hose Kit for All Flusher Hoses

•

Manual Handheld Air Purge w

Venting Cap

•

Long Handle with Hose Hooks

•

Hose-Holding and Tool Tray-Holding Bracket

Spin On Filter Cross Reference Guide

*KEEP FOR FUTURE REFERENCE*

Filter

G-Tec

Fram

Super

Tech

Motorcraft

STP

Non By-Pass

NBP2

PF34/PF1232 PH3682

ST2827 FL13B/FL839 S-2827

By Pass*

BP1

PF2

PH8A

S-01

FL1A

S-01

*By-Pass filters must always be on the left side of bracket (standing at handle end)

Summary of Contents for Basic TTCF-6












Search results

Summary of Contents for Basic TTCF-6

Reviews:

Related manuals for Basic TTCF-6

Brands by name

Popular brands

G-Tec Basic TTCF-6, How To Operate

Search results

Summary of Contents for Basic TTCF-6

Reviews:

Related manuals for Basic TTCF-6

Brands by name

Popular brands