background image

16 

REV 1/20 

 

 

GB2600 / GB2600A INTALLATION TOOL S/N: 1001 AND ABOVE  

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS

 

TEFLON® IS A REGISTERED TRADEMARK OF E.I. DUPONT DE NEMOURS & CO. LUBRIPLATE® IS A REGISTERED TRADEMARK OF FISKE BROTHERS REFINING CO. SLIC-TITE® IS A REGISTERED 
TRADEMARK OF LA-CO INDUSTRIES INC. LOCTITE® IS A REGISTERED TRADEMARK OF HENKEL CORPORATION. HUCK® IS A REGISTERED TRADEMARK OF ARCONIC INC.  

The GB940 Hydraulic Power Unit is a light-weight, portable power 
source designed to operate on a wide range of hydraulic installation 
tools. The unit is electrically powered and delivers up to 10,000 psi (689.5 
bar) working pressure with simple adjustable hydraulic outputs. The 24 volt 
remote control circuit, in the installation equipment, controls the pump 
output directional valve. The GB940 Hydraulic Power Unit is available in 
115 volt or 230* volt, single phase, alternating current. Output pressures 
as shipped are: PULL 5400-5700 psi, RETURN 2200-2400 psi. 

 

The GB940 Hydraulic Power Unit is available separately or in kits in-
cluding hydraulic quick-disconnect couplers, electrical connectors and 
hose cord kits in various lengths. 

 

GB940-12  includes the GB940 and 12 ft. (3.7 m) Hose Kit, part #940701 
GB940-26  includes the GB940 and 26 ft. (7.9 m) Hose Kit, part #940705 

  GB940-38  includes the GB940 and 38 ft. (11.6 m) Hose Kit, part #940709 
  GB940-52  includes the GB940 and 52 ft. (15.8 m) Hose Kit, part #940714 

GB940 POWER UNIT 

Power Units Available 

(Sold Separately)

 

The GB910 Hydraulic Power Unit is a portable power source designed to oper-
ate a wide range of hydraulic installation tools. The unit air powered, air actuated 
and delivers up to 10,000 psi (689.5 bar) working pressure. The actuator on 
the  installation  tool  remotely  controls  the  hydraulic  oil  directional  flow.  The 
unit consists of a two position air hydraulic pump, four way control valve and 
relief valve mounted on the reservoir. 

 

The  GB910  Hydraulic  Power  Unit  is  available separately  or  in kits  including 
hydraulic  quick-disconnect  couplers,  air  connectors,  air  lines  and  hydraulic 
hoses in various lengths. 

 

  GB910-12  includes the GB910 and 12 ft. (3.7 m) Hose Kit-Air, part #910701 
  GB910-26  includes the GB910 and 26 ft. (7.9 m) Hose Kit-Air, part #910705 

    GB910-38  includes the GB910 and 38 ft. (11.6 m) Hose Kit-Air, part #910709 
    GB910-52  includes the GB910 and 52 ft. (15.8 m) Hose Kit-Air, part #910714

 

GB910 POWERUNIT 

Image may not reflect actual tool 

Image may not reflect actual tool 

Summary of Contents for GB2600

















Reviews: