background image

Rev. 5/15 

 

GB50 S/N: 1476 AND ABOVE  

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. 

TABLE OF CONTENTS

 

Description

                                                                                                                             

Page

 

 

Warnings ..................................................................................................................................................................................... 3 
 
Principle of Operation and Air Exhaust ................................................................................................................................... 4 
 
How to use the GB50 ................................................................................................................................................................. 5 
 
Description and Maintenance ................................................................................................................................................... 6 
 
Parts Lists ................................................................................................................................................................................... 7 
 
Nose Assembly Selection Chart ............................................................................................................................................... 8 
 
EU Conformity and Warranty .................................................................................................................................................... 9 

 

SPECIFICATIONS

 

 

 

 

 

Hand Held Weight 

-   1.80 lbs. (0.82 kg) 

 

 

 

Air pressure req'd 

-   90-100 p.s.i. (6.2-6.9 bar) Max. 

 

 

 

Air consumption 

-   .29 SCF/cycle (8.21 L/cycle) 

 

 

 

Setting stroke 

-   .740" (18.8mm) 

 

 

 

Noise level   

-   81.5 dB (A)

 

 

                                 

Rated pull load 

-   600 lbs. (2.67kN) 

 

 

 

Vibration 

 

-   Tested– No hazards found. 

 

 

Summary of Contents for GB50










Reviews: