Gage Bilt GB745SH-12 Original Instructions Manual Download

Page: 4 / 32

REV 6/22

GB745SH

12 INSTALLATION TOOL S/N: 1006 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

SPECIFICATIONS

Hand Held Weight

2.25 lbs. (1.02 kg)

Air pressure req'd

100 p.s.i. (6.2

6.9 bar)

Air consumption

.30 SCF/cycle (8.50 L/cycle)

Hydraulic oil

Automatic Transmission Oil,

Dexron® III, or equivalent.

Setting stroke

.620" (15.75 mm)

Rated pull load

6,300 lbs. (28.02 kN)

Noise level

Less than 80 dB(A)

Vibration

Tested–

No Hazards Found

DESCRIPTION

WARNING

Any other use is forbidden.

ENVIRONMENTAL USE

WARNING

Do not operate in an explosive atmosphere.

The GB745SH

12 can be operated between 0ºF

118ºF (

17.8ºC / 47.8ºC)

The GB745SH

12 is a pneumatic

hydraulic split handled installation tool designed specifically for the efficient installation of blind

rivets, lockbolts and MAGNA

GRIP® fasteners. This tool

’

s unique "split" system provides the operator with a lightweight ergonomic tool. The

head assembly when held in hand weighs 2 1/4 lbs. (1.02 kg). The entire split installation tool weighs 10 1/2 lbs. (4.76 kg). It has

.620” (15.75

mm) fastener setting stroke.

The GB745SH

12 split handle installation tool operates on 90 to 100 psi (6.2

6.9 bar) of air pressure, with 90 psi. (6.2 bar) providing the maximum

efficiency. At 90 psi. (6.2 bar) of air pressure, the GB745SH

12 does not exceed 80 dB(A) and consumes .30 SCF/cycle (8.50 L/cycle).

The air inlet is provided with 1/4

18 female pipe thread for accepting the user's air hose fitting.

The GB745SH

12 comes with 12 feet (3.7 m) of hose. Pull pressure varies with different length hoses. When ordering specify the shortest length

hose possible for your application this will provide optimum pull pressure. For example if your application only requires 5 feet (1.5 m) of hose order

riveter with

5 suffix (GB745SH

5). Please consult our engineering department for specific applications.

NOSE ASSEMBLIES ARE NOT FURNISHED WITH THIS TOOL AND MUST BE ORDERED SEPARATELY. (See nose assembly selection

chart on pg. 23).

Summary of Contents for GB745SH-12

































Search results

Summary of Contents for GB745SH-12

Reviews:

Related manuals for GB745SH-12

Brands by name

Popular brands

Gage Bilt GB745SH-12, Original Instructions Manual

Search results

Summary of Contents for GB745SH-12

Reviews:

Related manuals for GB745SH-12

Brands by name

Popular brands