Gage Bilt GB784 Original Instructions Manual Download | Manualshive

Page: 21 / 24

background image

21

Rev. 2/17

GB784

681 PULLING HEADS

FOR 2000 SERIES CHERRYLOCK

®

RIVETS

CONFORMING TO NAS 1400 & NAS 1740

INSTALLING 681 PULLING HEAD ON RIVETER

1. Remove knurled cap from front of riveter head.
2. Place jaw assembly (C) inside collet (B).
3. Insert spring end of jaw assembly into hole of head piston. Apply enough pressure to engage
  collet threads. Turn until collet bottoms on shoulder of piston and collet lock snaps into slot in
  piston. Hand tight is sufficient.

NOTE: To remove collet, push collet lock back into collet (using a blunt pointed tool) turning the
collet clockwise.

4. Place sleeve assembly (A) over collet and head piston. Slip knurled cap over the sleeve
assembly and hand tighten onto end of riveter head.

ACCESSORIES

(SOLD SEPARATELY)

NOSE ASSEMBLY SELECTION CHART

RIVET

NOSE

DIAMETER ASSEMBLY

A

B

3/32"

3U-681-25

.188

.348

3/32"

3C-681-25

.163

.332

1/8"

4U-681-25

.250

.341

1/8"

4C-681-25

.208

.377

5/32"

5U-681-25

.313

.377

5/32"

5C-681-25

.269

.352

3/16"

6U-681-25

.375

.418

3/16"

6C-681-25

.335

.386

1/4"

8U-681-25

.500

.452

1/4"

8C-681-25

.458

.398

DIMENSION

TOOL CAPACITY CHART:

The numbers shown in the rivet columns below are the maximum grip length that can be installed with this tool. Dashes indicate
those rivets sizes which cannot be installed in any grip length.

Gage Bilt certifies the GB784 will install the fasteners listed below

*May require 95 PSI at tool.

**Indicates maximum grip

*

*

*

*

*

*

*

*

*

*

*

*

**

**

GB784

ALL
ALL

ALL
ALL
ALL

ALL

ALL

CTSK.

HEAD

-4
-5
-6

ALL
ALL

2539

2538

ALUMINUM

MONEL

BULBED CHERRYLOCK

®

ALL

XX-681-25

ALL
ALL

UNIV.

HEAD

GAGE BILT

TOOL

2239
2249

NOSE

ASSEMBLY

RIVET

DIAMETER

UNIV.

HEAD

CTSK.

HEAD

2238
2248

-4

ALL

ALL

ALL

ALL

ALL

ALL

-5

8**

8**

8**

9**

8**

9**

-6

8**

8**

8**

9**

8**

9**

-8

8**

8**

8**

9**

-

-

GB784

XX-681-25

GAGE BILT

TOOL

STANDARD CHERRYLOCK

®

(NAS1398/99 & HS4464 & HS5413)

NOSE

ASSEMBLY

2643
2653
2663

UNIV.

HEAD

2563

UNIV.

HEAD

2642
2652
2662

CTSK.

HEAD

RIVET

DIAMETER

ALUMINUM

MONEL

STAINLESS

2562

CTSK.

HEAD

2162
2262

CTSK.

HEAD

UNIV.

HEAD

2163
2263

Nose assemblies are not furnished with the tool and must be purchased separately. In ordering heads be sure to specify the
shank diameter and head style (universal or countersunk) of the rivets to be installed.

The following pulling heads will fit directly on the GB784 Riveter. (NOTE: Cherry® 681 series pulling heads fit directly on the GB784).

«
...
19
20
21
22
23
...
»

Summary of Contents for GB784

























Reviews:

No comments

Related manuals for GB784

Brand: Hama Pages: 46

Brand: Gallagher Pages: 33

Brand: Gage Bilt Pages: 9

Brand: Gage Bilt Pages: 13

Brand: Gage Bilt Pages: 24

Brand: Nederman Pages: 120

Brand: Ancor Pages: 12

Brand: Cannondale Pages: 12

Brand: Siser Pages: 76

Brand: Eastwood Pages: 8

Brand: Paslode Pages: 32

Brand: Scheppach Pages: 48

Brand: Chicago Pneumatic Pages: 36

Brand: joke Pages: 12

2000-2 LNB Series

Brand: Cross Technologies Pages: 8

Brand: Omer Pages: 2

Nanogun Airmix H2O

Brand: SAMES KREMLIN Pages: 67

Brand: Fein Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands