9
Cleaning and maintenance
m
Risk of burns!
The appliance becomes hot during operation. Allow the
appliance to cool down before cleaning.
m
Risk of electric shock!
Penetrating moisture may result in an electric shock.
Clean the appliance using a damp cloth only. Before
cleaning, pull out the mains plug or switch off the circuit
breaker in the fuse box.
m
Risk of electric shock!
Do not use any high-pressure cleaners or steam
cleaners, which can result in an electric shock.
m
Risk of injury!
Risk of falling when working on the appliance. Use a
stable stepladder.
m
Risk of injury!
Components inside the appliance may have sharp
edges. Wear protective gloves.
Cleaning agents
To ensure that the different surfaces are not damaged
by using the wrong cleaning agent, observe the
information in the table. Do not use any of the following:
▯
Harsh or abrasive cleaning agents,
▯
Cleaning agents with a high alcohol content,
▯
Hard scouring pads or cleaning sponges,
▯
High-pressure cleaners or steam cleaners.
Wash new sponge cloths thoroughly before use.
Follow all instructions and warnings included with the
cleaning agents.
Removing metal grease filter
m
Risk of injury!
Risk of falling when working on the appliance. Use a
stable stepladder.
m
Risk of injury!
Components inside the appliance may have sharp
edges. Wear protective gloves.
1
Press the marking on the metal grease filter and
remove the metal grease filter from the holder.
While doing this, place your other hand under the
metal grease filter
Note:
Grease may accumulate in the bottom of the
metal grease filter. Hold the metal grease filter
level, otherwise grease will drip out.
2
Clean the metal grease filter.
3
Clean the appliance from the inside.
Area
Cleaning agent
Stainless steel
Hot soapy water:
Clean with a dish cloth and then dry
with a soft cloth.
Clean stainless steel surfaces in the
grind direction only.
Special stainless steel cleaning prod-
ucts are available from our after-sales
service or from specialist retailers.
Apply a very thin layer of the cleaning
product with a soft cloth.
Painted surfaces
Hot soapy water:
Clean using a damp dish cloth and dry
with a soft cloth/towel.
Do not use any stainless steel cleaners.
Aluminium and
plastic
Glass cleaner:
Clean with a soft cloth.
Glass
Glass cleaner:
Clean with a soft cloth. Do not use a
glass scraper.
Controls
Hot soapy water:
Clean using a damp dish cloth and dry
with a soft cloth/towel.
Risk of electric shock caused by pene-
trating moisture.
Risk of damage to the electronics from
penetrating moisture. Never clean
operating controls with a wet cloth.
Do not use any stainless steel cleaners.
Area
Cleaning agent
Summary of Contents for AC 402
