Gaggenau CG270110F, Installation Instructions Manual

To use this appliance in France, it is necessary to 

remove the L-tube mounted in the factory and assemble

the one supplied in the accessory bag. Fig. 6. Do not 

forget to insert the seal. If, for some reason, the L-tube

should be twisted, it is necessary to make sure that this

area is properly sealed. Make sure that all connections 

performed are free of leakage. 

The manufacturer does not accept any liability for leakage

on connections performed by the installer or if the L-tube is

moved or twisted.

4

-Check the voltage and total power on the 

characteristics plate. The appliance must be EARTHED. 

Make sure that connection has been performed in 

accordance with legal regulations in force for the country

in question and complies fully with the conditions laid

down by the local electricity company. 

In order to meet normal safety standards, the installer must

supply an all-pole circuit breaker with a contact aperture of

at least 3 mm. This is not necessary when connection is

made via a socket, so long as this is accessible to the user. 

Appliances equipped with plugs should only be connected

to sockets which are duly earthed. 

The appliance is type "Y". This means that the input supply

cable cannot be changed by the user. Only the brand's

service technicians are qualified to replace this cable. Use

the right cable type and section. 

Do not tamper inside the appliance. If necessary, call our

Service Centre. 

Hobs with control knobs are supplied with a plugged or

unplugged power cable.
TYPES OF CABLE

5

-In order to complete the installation process, you must

place the diffusers and the tops of the burners on their

corresponding burners. Also you must place the grids

correctly on their supporting elements. Fig. 7. 

Changing the type of gas

Before connecting the appliance to the supply, check that
it is prepared for the type of gas in question. Our hobs
leave the factory set for the gas type indicated on the 
characteristics plate. 
Depending on the regulations in force in your country, this
hob may be adapted to work with other types of gas (see
characteristics plate). To adapt the gas type, proceed as
follows: 

1 

-Remove the grates, covers and burner core. 

2

-Change the injectors using a 7-mm socket wrench and

be sure to tighten them down properly so that they are fully 
air-tight. Fig. 8. 
It is not necessary to adjust the primary air on these 
burners. 

B )

Adjusting reduced consumption on the burner valves.

1

- Set the valves to minimum.

2

- Remove the control knobs from the valve shafts. Fig. 9. 

3

- It has a flexible rubber seal. Simply apply pressure with

the tip of the screwdriver to release the thread toward the
tap´s adjusting screw. Fig. 10.

Do not remove the disc seal.
4

-Adjusting the by pass screw. 

For Propane and Butane Gas: the screw must be 
tightened down fully. 
For Natural Gas: turn the screw in an anticlockwise 
direction until the correct release of gas is reached: when
the burner is changed from the maximum to minimum 
settings, the flame does not go out or backfire. 

protect against any liquids that may spill from the hob.

6

- Re-assemble the control knobs. Never dismount the

C) Put the label which indicates the type of gas the
appliance has been adapted to near the characteristics
plate. 

Rigid connection. 

its factory-set position. 

All gas               3 x 0.5 mm2

Power cable:      

Hob: 

en

an authorised installation engineer, respecting  

of the gas and electricity providers.  

conversion to other types of gas must be carried out by 

All operations relating to installation, regulation and 

You are recommended to contact the Technical  

applicable regulations, standards and the specifications 

Assistance Service to convert to another type of gas. 

and gas supply.

Before you begin, turn off the appliance' s electricity 

A )

Changing the injectors on the burners (see table II). 

3

-The end of the input collector on gas hobs comes with a

Hotplates connection

In either of the cases, do not move or twist the L-tube from

and passing the tube through spaces liable to get blocked. 

tube and moving parts on the housing (e.g. drawers) 

If this method is used, avoid both contact between this 

Connection to a flexible metal tube (L min. 1m. - max. 3m.)  

1/2” (20.955 mm) threaded L-tube, Fig. 3a. This caters for: 

5

- It is important that all the reinforcement rings are in

the entire valve. 

place in order to ensure that the electrics are sealed to 

valve shaft (fig. 11): in the event of damage, change