background image

12

en-us

    Customer Service

Check the Installation

9

CAUTION

Before you plug in an electrical cord or turn on 
power supply, make sure all controls are in the OFF 
position.

Remove everything from the cooktop surface including 
stickers. Clean cooktop surface with cooktop cleaning 
cream.

Switch on the circuit breaker.

Verify that elements function properly.

Customer Service

Customer Service

If your appliance needs repairs, our Customer Service is 

there for you. We work hard to help solve problems 
quickly and without unnecessary service calls, getting 
your appliance back up and running correctly in the least 
amount of time possible.

When you call, please indicate the product number 
(E-Nr.) and serial number (FD-Nr.) so that we can support 
you in a qualified manner. You will find the data plate with 
these numbers on the bottom of the appliance. To avoid 
having to search when you need it, you can enter your 
appliance data and the Customer Service telephone 
number here.

Please read the use and care instructions provided with 
your appliance. Failure to do so may result in an error in 
using the appliance resulting in unnecessary service 
calls, which may not be covered by the warranty. 

Please find the contact data of all countries in the 
enclosed customer service list.

To book a service visit and product advice

E-Nr.

FD-Nr.

Customer Service 

O

USA

877

 

442

 

4436 

toll-free

CANADA

877

 

442

 

4436 

toll-free

Summary of Contents for CI 292 601













Reviews: